







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Roofing: The Los Angeles Owner’s Guide
If you own a Unilock roofing system and a part has failed, our team installs Unilock-compatible roofing components across Los Angeles, typically at installed prices of $470 – $2,125 for targeted repairs and $9,440 – $23,600 for a full roof replacement, scheduled around your written estimate rather than a rushed same-day promise. Most Los Angeles owners don’t spot the failure until it’s obvious: a dark water stain spreading across a ceiling, granules collecting in the gutter, or a tile that’s cracked after a hot, dry summer. That’s usually the point where the part has already been failing quietly for months. We’re an independent service provider, not affiliated with Unilock, and we’ll tell you plainly whether a repair or a replacement is the right call before any tool comes out.
Key Takeaways
- Targeted Unilock roof repairs in Los Angeles run $470 – $2,125 installed; full replacement runs $9,440 – $23,600.
- Unilock systems often fail at the flashing and tile-adjacent seams first, not the field of the roof.
- Every completed job is covered by the 365-Day Done Right Promise, in writing.
- We quote a written price before work begins: no numbers that move at the door.
Which Unilock Models This Applies To

Unilock is best known in Los Angeles for its hardscaping and paver lines, and a fair number of local homes carry Unilock-branded roof and coping components (roof tiles, cap pieces, and related trim) that match those systems. If you’re trying to pin down the right part, start with the label: most Unilock components carry a stamp or printed mark on the underside or back edge with a series code and dimensional spec. Measure the piece in place, length, width, and thickness, and write those numbers down before you call anyone.
Here’s the compatibility gotcha that trips up a lot of homeowners: the field tile and the cap or trim piece almost never come from the same series code, and a part that’s the right footprint can still be the wrong thickness for the existing substrate. That’s the mismatch we see most often in Los Angeles, where a slightly off-spec piece sits proud of the surrounding field and traps water at the seam. When we source a replacement, we compare against the number stamped on your existing part first. A genuine OEM match is ideal when it’s available. A quality aftermarket equivalent that meets the same dimensional spec is a legitimate option, and we’ll say so honestly rather than pushing the pricier route.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Roofing Is Failing
- Granule loss in the gutters. A handful of granules after a rain is normal. A steady accumulation means the surface layer is wearing through, and the part is aging faster than the rest of the roof.
- Water staining on ceilings near walls. This usually points to failed flashing or a seam around a Unilock cap piece, not the field of the roof itself. The stain appears inside long after the leak started outside.
- Cracked or lifted tiles after a hot spell. Los Angeles thermal cycling (cool nights, 90-plus-degree afternoons) stresses the fasteners and adhesive under rigid components. Visible lift is the part telling you it’s lost its seat.
- Visible seam separation at penetrations. Chimneys, vents, and skylights are where Unilock systems work hardest. Gaps there are the most common source of active leaks we’re called to in Los Angeles.
- Interior musty smell or damp attic framing. By the time you smell it, moisture has been traveling a while. This means the part failed quietly and needs a proper look, not a patch.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For Los Angeles, a targeted Unilock roof repair runs $470 – $2,125 installed, and a full roof replacement runs $9,440 – $23,600. Tile-specific repairs, common with Unilock components, land at $710 – $2,950. What moves the range: the number of parts being replaced, whether the substrate underneath needs repair once the old part comes up, roof pitch and access, and whether flashing has to be rebuilt at a penetration.
We quote parts and labor as separate line items in writing before work starts. The installed price covers the part, the fasteners and sealant, removal of the failed component, and cleanup. Every completed job is backed by the 365-Day Done Right Promise: if the work doesn’t hold within a full year, we come back and correct it at no charge. That’s the whole deal, in writing, before a tool comes out.
DIY or Call Us?
Some things are safe to check yourself. You can inspect from the ground with binoculars, note the label number on a part you can reach safely, and confirm where a stain is on your ceiling. We’d rather you do that than guess.
The part where DIY goes wrong is on the roof. Roof work involves height, steep pitch, and the real risk that lifting an adjacent component to swap one part breaks the seal on the next. A part swapped at the wrong thickness traps water at the seam, and you won’t know until the next rain. We don’t give you step-by-step roof instructions because the honest answer is that a trained crew belongs on that pitch. Our technicians have up to 22 years of experience, and we’ll tell you on the phone whether your symptom sounds like a small fix or a bigger job. Call (844) 343-6681 and we’ll walk you through it before you commit to anything.
FAQs

How long does a Unilock roof part last in Los Angeles? A properly installed Unilock roof component typically holds 15 to 30 years depending on series and sun exposure. Los Angeles UV intensity wears surfaces faster than coastal climates, so parts on south-facing slopes age quickest. If yours is past its midpoint and leaking, call (844) 343-6681 for a free estimate.
Can the failed part be repaired instead of replaced? Sometimes yes. A single lifted or cracked component with sound substrate around it can often be repaired. If the failure is at flashing or the substrate is soft underneath, replacement is the honest answer. We tell you which on the estimate.
How long does the replacement take? A single-part repair is usually a few hours. A full roof replacement on a typical Los Angeles home runs several days, weather permitting. We schedule around your written estimate and don’t try to rush work that needs proper curing.
How do you source the Unilock part? We work from the label number and measurements you provide, match them against the series spec, and source an OEM piece when available or a spec-matched quality equivalent when it’s the practical route. Every project gets a written price before work begins. Call (844) 343-6681 for a free estimate.
Other premium brands we work with include KraftMaid, Cambria, and Silestone, so your home’s specs stay traceable across the whole job. If a Unilock roofing part has failed and you want a straight answer on repair versus replacement, give us a call at (844) 343-6681 to schedule your free estimate. We answer with a live person 24/7, put every price in writing before work starts, and stand behind the finished job with the 365-Day Done Right Promise.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












