







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Bathroom Remodeling: The Los Angeles Owner’s Guide
Unilock bathroom remodeling installations in Los Angeles typically run $10,620 to $33,040 for a full bath, with smaller footprint projects landing between $5,900 and $14,160. We install Unilock-compatible systems with a written price before any work starts. In most cases an owner finds out something’s wrong the same way: a grout line in the shower pan that won’t stay sealed, a wall tile that sounds hollow when you tap it, or a slow weep from the joint where the Unilock curb meets the slab floor.
Los Angeles bathrooms take a specific beating. Hard water out of the LADWP supply leaves mineral scale on Unilock’s surface glaze faster than in softer-water markets, and the seasonal swing between dry Santa Ana weeks and winter rain pushes movement through wall assemblies that a properly bedded Unilock system should absorb without cracking. When it doesn’t, you’re looking at a failing substrate or a bond failure, not a cosmetic problem.
Key Takeaways
- Full Unilock bath remodeling in Los Angeles: $10,620 to $33,040; small bath: $5,900 to $14,160.
- The most common failure is a compromised substrate, not the Unilock surface itself.
- Every Bradford project gets a written price before work begins and the 365-Day Done Right Promise.
- A live person answers (844) 343-6681 any hour, any day.
Which Unilock Models This Applies To

Unilock’s bathroom line spans shower pans, wall systems, and curb-and-slope assemblies, and the compatibility question is almost never the surface tile itself. It’s the substrate underneath. The Unilock system you have dictates which drain flange, slope ratio, and waterproofing membrane you need, and those parts are not interchangeable across series. Getting this wrong is the single most expensive mistake we correct in Los Angeles bathrooms.
To identify your system, pull the original build paperwork if you have it, or look for a manufacturer label stamped on the underside of the shower pan or the back of a wall panel. If neither turns up, we measure the drain centerline to the nearest stud, the curb depth and height, and the pan footprint. Those three dimensions will usually pin the series. If your Unilock drain body is bonded in correctly, the smart money is on keeping it and matching a membrane, not tearing out a serviceable assembly to chase a part number.
OEM vs. Quality Aftermarket for Unilock
Unilock’s own replacement components carry a spec sheet and manufacturer warranty that trace directly to your assembly, which is why we default to them when they’re available. Aftermarket equivalents that meet the same spec (drain bodies, bonding flanges, setting materials) can be a legitimate option when time or availability is tight, and we’ll tell you plainly when one is a real match versus a lookalike. We don’t stock parts and we don’t carry any on a truck; every component is sourced against your model before the crew is scheduled. Bradford Remodeling Co Los Angeles is an independent service provider and is not affiliated with Unilock.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Bathroom Remodeling Is Failing
Here are the five symptoms we see most in Los Angeles, each with what’s actually going on underneath.
- Grout cracking along the shower floor perimeter. The pan or curb is moving because the substrate wasn’t set solid or the slab isn’t cooperating with a rigid bedding. Surface re-grouting hides it for a season and then fails again.
- Hollow sound when you tap wall tile. The setting material has debonded from the Unilock panel or the wall behind it. A small hollow is cosmetic; a spreading one signals water is already behind the surface.
- Mineral haze that won’t buff out. Los Angeles hard water etches some glazed surfaces once the factory seal wears. If the haze keeps returning after a proper descale, the glaze is compromised, not just dirty.
- Sagging or soft spot at the curb. This is a substrate failure, often from long-term moisture bypass behind the waterproofing. It’s the one you don’t want to ignore.
- Recurring musty odor with no visible water. A slow weep behind the assembly is feeding mold in the wall cavity. By the time you smell it, the membrane has usually been breached for months.
Replacement Cost & What’s Included

For a Los Angeles bathroom, a full Unilock system replacement runs $10,620 to $33,040. A small bathroom remodel sits at $5,900 to $14,160. A walk-in shower installation lands between $5,310 and $14,160, and a tub-to-shower conversion is $4,130 to $11,800. Those are written-price numbers, not estimates that move once work starts.
What drives the range: the condition of the substrate you’re working over, whether the drain and slope need redoing, tile or panel selection, and whether a permit is required for the plumbing changes. Our line-item quote separates parts, labor, and any permit cost so you can see exactly where the money goes. Every project carries a written price before we start and the 365-Day Done Right Promise: if a completed component fails within the guarantee window, we come back and correct it at no charge. We also work with a documented brand roster including KraftMaid, Cambria, and Silestone when the room needs cabinetry or surfaces beyond the Unilock system.
| Scope | Los Angeles Price Range |
|---|---|
| Full bathroom remodel (Unilock system) | $10,620 – $33,040 |
| Small bathroom remodel | $5,900 – $14,160 |
| Walk-in shower installation | $5,310 – $14,160 |
| Tub-to-shower conversion | $4,130 – $11,800 |
| Shower replacement | $3,540 – $10,030 |
| Bathroom vanity installation | $945 – $3,540 |
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
What you can safely do on your own: tap the tile to map hollow zones, check the drain and curb for movement, look for water staining at the floor joints, and clean the surface with a proper descale product to see whether the haze is fixed or the glaze is shot. Where a DIY repair typically goes wrong is the waterproofing. Re-grouting a shower floor looks simple, but if the substrate has moved or the membrane is breached, a surface patch just traps water behind a fresh barrier, and the mold and rot underneath keep spreading. Because Unilock systems depend on a continuous, correctly sloped waterproof assembly, a failed membrane is not something to patch from above.
If your Los Angeles Unilock bath has a soft curb, recurring odor, or spreading hollow zones, that’s a substrate failure, not a weekend grout job. Call (844) 343-6681 and we’ll schedule a free estimate with a written price in hand before any work starts.
FAQs

A correctly installed Unilock bathroom system typically holds 15 to 25 years in Los Angeles conditions, but the local water and seasonal movement are the deciding factors. Hard water accelerates glaze wear and mineral buildup on the surface, and the swing between dry Santa Ana spells and wet winter weeks moves the slab and framing underneath. Systems that were bedded on a properly prepped substrate and kept up with regular descaling tend to reach the top of that range; ones that skipped maintenance fail earlier. Call (844) 343-6681 for a free assessment of your specific assembly and estimates are free.
Often, yes. A local grout repair on a solid, movement-free pan is worth doing before you commit to a full replacement. But a compromised substrate, soft curb, or recurring mold behind the waterproofing means a repair just delays the failure, and the honest answer is replacement. We’ll tell you which side of that line your Los Angeles bathroom is on during the free estimate. Call (844) 343-6681 to schedule one.
A shower replacement alone runs $3,540 to $10,030 and typically takes a few days depending on how far the substrate repair reaches; a full Unilock bath remodel is a longer timeline and we’ll put the exact schedule in the written scope. Weather isn’t usually the factor indoors, but curing and inspection windows are. You’ll get the day-by-day plan before the crew arrives. For a firm date, call (844) 343-6681.
We match the component to your model from measurements, drain centerline, and curb dimensions when paperwork is missing, and we source it before scheduling the job. We don’t keep parts in stock, so every component is ordered against your specific assembly. If an OEM part is delayed, we’ll walk you through a spec-matched aftermarket alternative and its trade-offs before you decide. Call (844) 343-6681 and we’ll start with the measurements.
Get a Written Price on Your Los Angeles Unilock Bath
When a Unilock bathroom system fails, the cost of guessing is time and a second repair. Bradford Remodeling Co Los Angeles gives you the range up front, separates parts from labor on the quote, and backs the finished work with the 365-Day Done Right Promise. Background-checked technicians on every job, a live person answering the phone any hour, and a written price before a single tool comes out. Call (844) 343-6681 for your free estimate.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












