







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Therma-Tru Bathroom Remodeling: The Los Angeles Owner’s Guide
Bathroom remodeling in Los Angeles that includes Therma-Tru entry doors and door components typically runs $10,620 – $33,040 installed, depending on scope, fixtures and finishes. We handle the whole job under one written price, with a full-year guarantee on the finished work. Owners usually discover a problem with the Therma-Tru piece when the door that opens into their bathroom starts dragging, sticking, or letting in a draft near the hinge side, or when a hinge screw has stopped biting into the frame after a few Santa Ana heat cycles. The bathroom door is the most-moved door in most LA homes, and it shows wear first.
Whether you’re replacing just the door in a half-bath in Silver Lake or doing a full primary bath in Woodland Hills, the parts question is the same: match the right Therma-Tru component to the right opening, then build a remodel around it that passes inspection the first time.
Key takeaways
- Full bathroom remodel with a Therma-Tru door component: $10,620 – $33,040 in Los Angeles.
- The part that fails most is the door hinge or frame, not the slab or the hardware finish.
- We don’t stock or carry Therma-Tru parts on a truck. We source the correct replacement against your model, in writing, before install day.
- 365-Day Done Right Promise: if the work fails inside a year, we return and correct it at no charge.
- Bradford Remodeling Co Los Angeles is an independent service provider and is not affiliated with Therma-Tru.
Which Therma-Tru Models This Applies To

Therma-Tru bathroom doors are typically part of the Fiber-Classic, Smooth-Star or Profiles series, and the frame type is what determines which hinge and strike plates you need. The gotcha: a Smooth-Star slab measured at 80 inches tall and 32 inches wide will not accept the hinge pattern from a Fiber-Classic of the same nominal size, because the hinge prep geometry and mortise depth differ between series. Owners who order a hinge pack online by size alone are often surprised.
The correct part is identified three ways: the model and series label on the door edge or top rail, the hinge prep stamped on the frame jamb (look for the J-hinge or S-hinge mark), and a measured height and width of the door and the rough opening. We verify all three before quoting the part.
The OEM-versus-aftermarket decision is real. Therma-Tru OEM hinges and weatherstrip carry the manufacturer’s warranty, and we recommend them on any door still inside its factory coverage window. A quality aftermarket equivalent costs less and performs fine when the door is older and out of warranty – just make sure the finish matches and the hinge prep is confirmed against the specific series. We work with a documented roster of name-brand materials (Therma-Tru, KraftMaid, Cambria, Silestone) so specs stay traceable.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Therma-Tru Bathroom Remodeling Is Failing
- Door drags or rubs at the latch side. The hinge knuckles have worn and the slab has dropped, or the frame has shifted from humidity swings typical in older LA homes.
- Hinge screws spin without biting. The screw has stripped the jamb material after repeated opening and closing. This is the single most common failure we see on bathroom doors in Los Angeles.
- Drafty or visible gap at the perimeter. The weatherstrip or door gasket has compressed or lost its seal, most noticeable during June gloom or December cool snaps.
- Strike plate no longer lines up with the latch. The strike has been driven back or the door has swelled slightly in wet weather, misaligning the lock.
- Peeling or bubbling on the jamb finish. A slow leak at the shower or tub has wicked into the frame and started breaking down the primer coat. This one is worth a look from a pro before you repaint.
If two or more of those are true, the door component needs attention and it’s worth looking at the surrounding bathroom surfaces at the same time to rule out a moisture problem behind it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s where the price range lands for Los Angeles. A full bathroom remodel with a Therma-Tru door component runs $10,620 – $33,040. A small bathroom remodel is $5,900 – $14,160. A vanity installation on its own is $945 – $3,540. A shower replacement is $3,540 – $10,030, and a tub-to-shower conversion is $4,130 – $11,800.
The range depends on square footage, whether plumbing moves, the door component and frame swap, fixture tier and any inspection corrections. Every one of those line items is priced in writing before we start, and that price does not move at the door. Parts and labor are always separate lines so you know what the Therma-Tru piece cost versus the install labor. The finished work sits under the 365-Day Done Right Promise for a full year.
DIY or Call Us?
You can safely check hinge screws for bite, measure the door slab and rough opening, and read the series label. Those are worth doing before you call.
Where DIY goes wrong on a Therma-Tru door swap: rehanging a slab into a frame with a stripped hinge jamb usually makes the problem worse. The new screws need longer bite or glue-and-dowel repair, and an untrained install can rack the frame and cause the door to bind or fail to latch. That’s the point where most owners call us anyway – often after they’ve bought the wrong part.
One honest note: the bathroom door isn’t dangerous to work on, but if the frame is failing due to a leak behind the wall, correcting the door without addressing the moisture will just repeat the failure. We check both. Call (844) 343-6681 for a free written estimate.
FAQs

Expect 12 to 20 years for the door slab and hinges in LA’s climate, often less on a bathroom door that gets used ten to twenty times a day. Humidity swings in older homes and sun exposure on exterior-adjacent doors shorten that. Call (844) 343-6681 if yours is past 10 years and showing symptoms.
Often yes. If only the hinge jamb has stripped, a hinge screw repair with longer bite or a wood-dowel fix can extend the door’s life by several years and costs far less than a new slab. If the frame is cracked or the slab is warped, replacement is the honest answer. We’ll tell you which on a free estimate – call (844) 343-6681.
Door component replacement is typically a half-day to a full day. A bathroom remodel that includes the door swap runs several weeks depending on scope and permit inspection timing. Your written scope lists the exact install days – call (844) 343-6681 for a free estimate.
We match your model, series and hinge prep and source through manufacturer-authorized supply channels, with the part spec listed on the written quote before we order. Nothing is guessed by size alone. Call (844) 343-6681 for a free written estimate.
You’ve got a Therma-Tru door that’s tired and a bathroom that deserves a clean rebuild. Call Bradford Remodeling Co Los Angeles at (844) 343-6681 for a free estimate – a live person answers, 24 hours a day. You’ll get a written price before any work starts, a crew that shows up on time, and the signed 365-Day Done Right Promise in your hand at close. We work with KraftMaid, Cambria and Silestone on the cabinetry and surface side, and Therma-Tru on the doors.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












