







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Sterling Driveway & Pavers: The Los Angeles Owner’s Guide
We install Sterling-compatible driveway and paver systems across Los Angeles, and a full paver driveway usually lands between $8,260 and $21,240 installed, depending on square footage, base prep, and whether the old surface has to come out first. Sealing alone runs $295 to $825. We can usually get an estimator to your driveway within a few days, though the work itself is scheduled around weather and cure time, not rushed.
Owners rarely wake up to a paver problem. They notice it slowly: a low corner that holds water after a hose run, joints that wash out after the first real rain, or a paver that rocks underfoot near the apron. In Los Angeles, that first rain is often the diagnostic. Water pooling in one spot three days later tells you the base has shifted, not just the sand.
Key Takeaways
- Installed paver driveways in Los Angeles run $8,260 to $21,240; sealing is $295 to $825.
- Most “failed pavers” are failed base prep, not failed pavers.
- We’re an independent remodeling contractor, not affiliated with Sterling.
- You get a written price before work starts and a 365-Day Done Right Promise on the finished job.
Which Sterling Models This Applies To

Sterling has sold driveway and paver systems under several product lines, and the spec sheet matters more than the label on the box. The two things we check first are nominal paver thickness and the joint width the system was designed for. A 60mm paver set on a base built for 80mm will move, no matter how well the joints are filled. If your old install drawings are gone, the paver face dimensions and the edge restraint profile usually tell us the series.
Pull a label or a spare paver from the original pallet if you still have one. The mold number, the thickness stamp, and the finish code let us match color and dimension instead of guessing at a “close enough” blend. Sterling color lots vary by year, and an exact match is sometimes impossible on an older run. That’s where the OEM-versus-aftermarket call gets real: a current-production paver from the same series beats an aftermarket lookalike every time on fit, but an exact discontinued match may mean replacing a whole course rather than a handful of units.
Los Angeles adds a wrinkle. Much of the city sits on expansive clay soils that swell with winter moisture and shrink hard in summer. Paver systems that hold up here are built on a compacted aggregate base with proper drainage slope, not a thin sand bed. If your existing driveway was laid over a shallow base, a straight paver swap just resets the clock on the same failure.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Sterling Driveway & Pavers Is Failing
- Water pooling in a low corner. Standing water a day or two after rain means the base has settled or the slope was never right. Pavers don’t sag on their own; what’s under them does.
- Joint sand washing out after storms. Repeated loss of joint sand points to poor drainage or missing edge restraint at the perimeter. Without restraint, the whole field spreads.
- Paver rock or wobble underfoot. A single rocking unit usually means a broken base spot or a hollow beneath it. Left alone, the neighbors start to move too.
- Weeds and grass pushing through joints. Heavy growth between pavers signals the joint sand is gone and the base is holding moisture. Polymeric joint sand handles this better than plain sand in our climate.
- Visible cracks in individual pavers. Cracks across multiple units in a line usually trace to a base failure or vehicle load past the system’s rating. Isolated cracks are often impact damage.
In the older neighborhoods around the hillsides, we regularly see driveway failures that trace to a shallow base and a slope that dumps runoff toward the house instead of the street. That’s a drainage fix as much as a paver fix.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

A paver driveway installation in Los Angeles runs $8,260 to $21,240 installed. Full driveway replacement with demo and new base runs $5,900 to $16,520 if you’re switching to a simpler surface, and concrete driveway installation sits at $5,310 to $14,160. Resealing an existing paver drive is $295 to $825. Paver patio work, if the driveway project grows into the yard, is $4,130 to $12,980.
What moves you within the range: square footage, how much old surface gets torn out, base depth required by your soil, edge restraint and drainage work, and the paver series itself. Every quote is itemized: demo, haul-away, base material and compaction, pavers, edge restraint, joint sand, and cleanup. There’s no line that says “miscellaneous.”
Every completed install carries our written 365-Day Done Right Promise. If a settled corner or a joint failure shows up inside that year, we come back and correct it at no charge. You hold a signed guarantee before we leave the site.
DIY or Call Us?
Some things you can check safely. Walk the drive after rain and mark where water stands. Pull a loose paver to see what’s under it. Look at the edge restraint along the apron and the house side. If you see a hollow base, a missing restraint, or a joint pattern that’s washing out along a slope, the fix is a base repair, and that’s not a Saturday project.
Where DIY goes wrong on paver work: people reset units on fresh sand without addressing the base, and the failure returns within a season. Lifting and re-bedding a paver field over a bad base is heavy work with real injury risk, especially on a sloped drive. It’s also the exact scenario where a homeowner ends up paying twice.
If you’re not sure whether your pavers need a reset, a base repair, or a full replacement, call (844) 343-6681 and we’ll tell you straight. Estimates are free and there’s no pressure to book.
FAQs

The pavers themselves typically hold up 20 to 30 years or more. The base is what determines real-world lifespan in Los Angeles, where clay soils and dry-then-wet cycles stress a shallow base. A properly built base with drainage outlasts the pavers on top of it.
Often yes. If the pavers are sound and the failure is localized, we can lift the affected area, rebuild the base, and reset the original units. Full replacement makes more sense when the base is failing across the whole drive or the pavers are cracked and discontinued. Call (844) 343-6681 for a free look.
A typical residential driveway takes several days from demo through final joint sand and cleanup, longer if base depth or drainage work is heavy. We don’t promise a same-day install. You’ll get a written schedule with the written price before work starts.
We work from your existing paver dimensions, thickness, and finish code, and match against current Sterling series or a documented equivalent from our hardscaping brand roster. Where an exact color match isn’t available, we tell you upfront and show the options before any material is ordered. We don’t carry parts on a truck; materials are ordered to spec.
If you’re ready to get a real number on your Los Angeles driveway, call (844) 343-6681 for a free estimate. We’ll walk the drive, explain what failed, and hand you a written price and a written guarantee before anything starts.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












