







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Los Angeles Owner’s Guide
Schluter systems are waterproofing and edge-protection assemblies, not a standalone appliance, so “replacing the Schluter part” on a home addition or ADU means replacing the failed membrane, profile, drain bonding flange or trim leg at the transition where it let go. In Los Angeles, an addition runs roughly $53,100-$153,400 and an ADU roughly $106,200-$259,600, and those numbers assume the waterproofing is done as a tested system. Owners usually find the failure the same way: a soft grout line at a shower curb, a hairline crack running under a metal edge profile, or a damp smell in a converted garage weeks after the tile looked finished.
We install Schluter-compatible assemblies on additions and ADUs across Los Angeles. Bradford Remodeling Co Los Angeles is an independent contractor and is not affiliated with Schluter; we work with the product, we don’t speak for the manufacturer.
Which Schluter Models This Applies To

The common failure points on Los Angeles additions and ADUs sit in a handful of Schluter lines. KERDI and KERDI-BAND handle sheet and seam waterproofing. DITRA and DITRA-HEAT are the uncoupling and heated-floor membranes. KERDI-LINE and KERDI-DRAIN are linear and point drains. KERDI-SHOWER trays and curbs build the pitched base. SCHIENE, RONDEC and JOLLY are the edge profiles. On a typical ADU we’re dealing with three or four of these at once, not one.
Identify what you have before you price anything. Read the printed lettering on the membrane fleece – DITRA has square dimples at roughly 3/16 inch on center, DITRA-HEAT adds heater wire clips, and KERDI is a flat brushed fleece with no dimples. Measure the profile leg width in millimeters; SCHIENE and RONDEC come in 3/8, 1/2, 9/16 and larger legs, and the wrong leg either lips over the tile or sits proud of it. Check the drain flange for a stamped model code and the tray for its size and offset.
OEM versus aftermarket matters more here than on most jobs. Schluter’s own bonding flanges, band and membrane carry the manufacturer’s system warranty and are tested together; a generic uncoupling mat or a hardware-store edge strip may fail at the seam because the fleece doesn’t bond the same way with modified thin-set. On an ADU where the shower or floor assembly is behind finished tile, the difference in price is a rounding error against the cost of tearing it out. We buy the matching OEM membrane and profiles. That’s the decision we’d make in our own homes.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
- Grout cracking in a straight line along a floor transition. That line is usually the membrane seam or the edge of the tray; it means movement or a poor bond, not just settling.
- A soft or hollow thud over a shower curb or bench. Water has gotten under the profile or the curb wrap and the setting bed is coming loose.
- Efflorescence or a white salt bloom at the base of a wall. Moisture is wicking through a break in the band behind the tile and drying out the surface, and it won’t stop on its own.
- A tile lifting at the edge of a metal profile. The profile leg is the wrong size for the tile thickness or wasn’t bedded fully, and it’s now levering the tile edge loose with every temperature swing.
- A damp smell or dark spot in an ADU bathroom or at a converted-garage slab edge. In Los Angeles, cool nights and warm days pull slab moisture and trapped water to the surface, so a small membrane break shows up as a recurring stain rather than a puddle.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Correcting a failed Schluter assembly on a Los Angeles addition or ADU lands in the broader project price you’d expect for the room it affects. Full additions run $53,100-$153,400 and full ADU construction $106,200-$259,600. A shower or wet-area membrane tear-out and rebuild inside an existing structure typically sits at the lower end of a bathroom remodel at $10,620-$33,040, and a small bathroom redo (often the ADU case) at $5,900-$14,160.
What moves the number: the size of the area that has to come out, whether the setting bed is sound enough to reuse, whether the drain or tray has to be replaced rather than re-bonded, and how much finish tile has to be matched. You get a written price before any work starts, itemized for membrane and profiles, labor and finish, so the numbers don’t shift at the door.
Every completed project carries the 365-Day Done Right Promise: a full-year written guarantee, and if the work fails inside that window we come back and correct it at no charge. All work is insured and bonded.
DIY or Call Us?
Some of this you can safely check. Peel back a loose tile edge to see whether the fleece is bonded, look for the printed membrane lettering, photograph the drain flange, and note where cracks or damp spots recur over a couple of weeks. Measuring the profile leg and writing down the model codes costs nothing.
What we’d steer you away from: cutting out and re-bonding membrane, re-setting a curb or tray, or tearing into a wet bed over a converted-garage slab without knowing where the waterproofing ends. The seam you can’t see is the one that leaks, and a redone flood test that fails costs more than the original repair. This is slow, technical work, and it’s the place a homeowner most often gets it wrong on the first pass.
Call (844) 343-6681 to schedule your free estimate. A live person answers, 24 hours a day, and we’ll tell you straight whether it’s a patch or a rebuild.
FAQs

How long does a Schluter membrane or profile last? A correctly installed, OEM Schluter assembly bonded over a sound substrate should hold through the life of the tile – ten to fifteen years or longer in an interior Los Angeles bathroom, and shorter on exterior or slab-on-grade ADU work where UV, soil movement and seasonal moisture do more of the damage. Lifespan depends on the bond and the drain detail, not the brand name.
Can it be repaired instead of replaced? Often, yes – a small membrane break, a lifted profile leg or a single failed seam can be cut out and re-bonded if the surrounding setting bed is sound. It has to be replaced, not patched, when water has reached the substrate, when the tray or curb is soft, or when the leak has been running behind tile for months. Call (844) 343-6681 and we’ll look before we quote.
How long does the swap take? A profile or localized membrane repair is typically a day or two. A shower membrane, tray and drain rebuild behind tile runs several days to a week because the setting and waterproofing have to cure before tile goes back. We give the schedule in writing at the estimate.
How do you source the part? We match the model and size from your existing material – the stamped drain code, the profile leg measurement, the tray footprint – and buy the OEM membrane, band, drain flange and profiles through supplier channels. We don’t claim stock or parts on a truck; we order to your spec. If you’re also planning kitchen work, we install KraftMaid, Cambria and Silestone alongside these projects.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












