







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Moen Driveway & Pavers: The Los Angeles Owner’s Guide
Bradford Remodeling Co Los Angeles installs and repairs Moen fixtures and the exterior hardscape that surrounds them, and a full paver driveway install in Los Angeles typically runs $8,260 – $21,240. We’re an independent service provider, not affiliated with Moen. The call usually starts with a small problem: a paver that’s heaved after a wet winter, a fixture base that’s backing out of its footing, or drainage that stopped working near the front walk. One loosened unit is how most homeowners find out the base under it has already failed.
Key Takeaways
- Paver driveway installation in Los Angeles: $8,260 – $21,240 installed.
- Concrete driveway: $5,310 – $14,160. Asphalt: $4,130 – $10,620.
- Every price is written down before work starts, and every completed project carries the 365-Day Done Right Promise.
- We work from a documented brand roster that includes Belgard and Unilock hardscape, with Moen parts sourced to match your exact model.
Which Moen Models This Applies To

Moen doesn’t sell driveway pavers. Moen makes faucets, shower valves, and outdoor fixtures, and those fixtures sit in and around hardscape – a hose bib set into a paver apron, a shower valve cartridge behind a tiled wall, an outdoor spigot at the base of a driveway bed. That’s where Moen and driveway work meet for most Los Angeles homeowners. Model identification matters, because the parts don’t cross over. A Moen 1222 cartridge (the classic single-handle shower valve) has no relationship to a Moen 1225 or the newer 1200 series. Measure the escutcheon and pull the model number off the trim ring or the inside of the valve body before you order anything.
Paver compatibility is a separate question. Moen fixtures are standard sizes, so the fit is universal. The pavers around them are not. Belgard and Unilock each run their own nominal dimensions and color-lot codes, and a replacement paver from the wrong lot will read as a patch from ten feet away. Check the pallet stamp or the original job invoice before you buy singles.
OEM or aftermarket?
For Moen cartridge work, OEM is the right call. Aftermarket cartridges for older Moen valves are a known source of drip-through and temperature swing, and the savings rarely hold up over a year. For pavers, staying with the original manufacturer is the same story: match the lot or accept the mismatch. We source both through documented suppliers so the spec is traceable on the invoice.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Moen Driveway & Pavers Is Failing
- Water pooling at the fixture base. A Moen hose bib or spigot that drips at the stem wets the base course and the paver bedding under it. Over a season, that soft spot heaves or settles.
- A paver that rocks when you step on it. The joint sand has washed out and the base has lost compaction. In Los Angeles, hot dry summers shrink and crack that sand, letting winter rain go straight through.
- Efflorescence – the white chalky film. It’s salts migrating out of the base. Sometimes it’s cosmetic. Sometimes it means water is sitting under the pavers because the drainage plane has failed.
- A Moen fixture cartridge that leaks behind the wall. That’s a plumbing failure, not a paver failure, but it’s often found because water shows up at the driveway edge or the wall base.
- Sunken or tilted stair nosings and walkway joints. Root movement and soil expansion do this. Uneven pavers are a trip hazard and a sign the subgrade needs correction, not just re-sanding.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Los Angeles pricing runs on square footage and removal weight. A full paver driveway installation is $8,260 – $21,240. Concrete driveway installation is $5,310 – $14,160, asphalt paving runs $4,130 – $10,620, and a full driveway replacement is $5,900 – $16,520. Resealing alone is $295 – $825 for a residential drive. Patios and walkways cost separately – a paver patio installation is $4,130 – $12,980.
The range covers removal and disposal, base prep and compaction, aggregate or sand bedding, paver or pour, edge restraint, and joint filling. If a Moen fixture set into the hardscape needs repair or replacement, that’s quoted as a line item. We give you the written price before a single tool comes out – no numbers that move at the door. Finished work is covered by the 365-Day Done Right Promise: if it fails within a year, we come back and correct it at no charge. We’re also glad to handle KraftMaid, Cambria, and Silestone work under the same standard if the project grows.
DIY or Call Us?
You can safely check a few things. Walk the driveway and mark any paver that rocks or sounds hollow. Look for white efflorescence. Check whether water pools near the Moen fixture or the garage apron after rain. Photograph the pallet stamp or lot tag if it’s still legible.
Where DIY goes wrong: re-sanding a joint sounds simple, but if the base has lost compaction, sand just hides a failure that returns next wet season. Lifting a paver to reset it without matching the bedding depth can tilt the whole row, and reinstalling a Moen cartridge without the right tool kit tends to score the valve body. We don’t carry parts on a truck. We source the correct Moen part and the matching paver lot before the crew arrives. Background-checked, uniformed technicians, a live person answering the phone around the clock, no voicemail queue. Call (844) 343-6681 and we’ll tell you honestly whether this is a re-sand, a repair, or a replace.
FAQs

A properly installed paver driveway typically lasts 25 to 30 years here, and the pavers themselves often outlast that. What fails first is the bedding and joint sand, which takes a beating from LA’s dry summers and wet winters. Re-sanding every 3 to 5 years stretches the life of the whole system.
Yes, in most cases. A Moen cartridge can be swapped without replacing the whole valve, and a single heaving paver can be reset if the base under it is sound. The repair-versus-replace call hinges on how many pavers are affected and whether the drainage plane under them still works. We’ll show you the failing area and give you a written number for both options. Call (844) 343-6681 for a free estimate.
A Moen cartridge swap takes about an hour once the correct part is in hand. Resetting a handful of pavers is a half-day. A full paver driveway replacement in Los Angeles runs 3 to 7 working days, depending on square footage, removal, and whether a new base course is needed.
We read the Moen model number off the trim ring or valve body, then order the matching OEM cartridge or trim kit through documented suppliers. For pavers, we pull the lot code from the pallet stamp or your original job paperwork and source from the same manufacturer, so the match holds. The model number and lot go on the written quote so you can see exactly what’s being installed.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












