







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Cover Driveway & Pavers in Los Angeles, CA
Cover Driveway & Pavers: The Los Angeles Owner’s Guide
If you’ve landed here, you already own a Cover driveway or paver system and something in it has failed. This page is built for exactly that: matching the right replacement part to your Cover model, giving you an honest installed price for Los Angeles, and getting the fix done without guesswork. Paver driveway installation in Los Angeles typically runs $8,260 – $21,240 installed, and driveway replacement runs $5,900 – $16,520; smaller section repairs land well below either figure.
Owners usually discover the failure the same way. A paver rocks underfoot on the walk from the car. A joint line that was tight last spring is now a half-inch gap after a summer of dry heat. Water pools against the garage slab instead of running to the street. Or a corner paver lifts entirely after a car tire catches it, exposing the sand-and-gravel bedding underneath. In every case the paver itself is rarely the problem. The setting bed, the base, or the joint sand has moved, and the paver is just telling you where.
Which Cover Models This Applies To

Cover’s driveway and paver line covers several generations, and the part you need depends on which one you have. Start by checking the underside of a loose paver or the edge restraint along the driveway perimeter, where the series and dimensions are usually stamped. Older series ran shallower pavers on a thinner base; newer lines run thicker units, which is why a replacement paver from the current catalog often won’t sit flush with a 10- or 12-year-old field. That’s the single most common compatibility gotcha we see in Los Angeles: the right color and texture, the wrong thickness.
Measure the failed unit in three dimensions before you order anything, and note the color name, not just “gray.” Cover’s dye lots shift slightly between production runs, so a fresh paver next to sun-faded neighbors will read a shade lighter for a season or two. That’s normal and it fades into the field.
For the OEM-versus-aftermarket decision: OEM Cover pavers are the safe match when you’re replacing a handful of units inside an existing field and want the profile to line up exactly. A quality aftermarket equivalent, sized and rated to the same thickness and compressive spec, is a reasonable option for edges, borders, and areas that will be cut anyway. Bradford Remodeling Co Los Angeles is an independent service provider and is not affiliated with Cover; we source and install to your model’s spec, not the other way around.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Cover Driveway & Pavers Is Failing
Here’s what a failing Cover driveway actually looks like, and what’s happening underneath each symptom:
- Pavers rocking or “walking” underfoot. The bedding sand has washed out or was never compacted to full depth, so the unit sits on air and moves every time it’s stepped on. Left alone, a rocking paver grinds its neighbors loose within a season.
- Joint sand washing out after rain. Los Angeles gets its rain in concentrated bursts, and a driveway that drains toward the house instead of the street will strip joint sand in a single storm. Refilling joints without fixing the slope just means you’ll refill them again next winter.
- Gaps opening between pavers. Usually the edge restraint has failed or was never pinned, so the field spreads outward at the driveway edges. Once the edge moves, the pattern loosens.
- Efflorescence: a white, chalky haze on the surface. That’s mineral salt drawn up through the paver from the base. It’s cosmetic, common in our climate, and often resolves; it’s also a signal that moisture is sitting under the field instead of draining.
- Sunken or heaved sections. The base wasn’t compacted in lifts to full depth, or roots and tree movement have pushed a section up. Heaving in a Los Angeles driveway is often a tree-root problem, not a paver problem.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what driveway and paver work runs in Los Angeles, installed. The range reflects square footage, base depth, access, and whether existing material gets hauled off:
- Paver driveway installation: $8,260 – $21,240
- Concrete driveway installation: $5,310 – $14,160
- Asphalt driveway paving: $4,130 – $10,620
- Driveway replacement: $5,900 – $16,520
- Driveway sealing: $295 – $825
- Paver patio installation (if the same failure hits a patio): $4,130 – $12,980
Every Bradford Remodeling Co Los Angeles project gets a written price before any work starts, itemized as parts, labor, base prep, and disposal. No numbers that move at the door. Completed work carries the 365-Day Done Right Promise: if the installation fails within that year, we come back and correct it at no charge. The written guarantee goes in your hand at job close, along with a clean site and a signed scope document.
DIY or Call Us?
The honest split: you can safely lift a single loose paver to inspect underneath, photograph the bedding sand, check whether the joint sand is gone, and confirm the edge restraint is still pinned. That inspection tells you whether you’re looking at one failed unit or a base problem, and it costs nothing.
Where DIY goes wrong is re-setting into an uncompacted base. A paver replaced over loose sand will rock again within weeks, and a homeowner who keeps patching the same spot ends up paying for the fix twice. Base prep, compaction in lifts, and correct drainage slope are the parts that decide whether the repair lasts a season or a decade. If the fix is larger than a handful of pavers, call us. We’ll give you a straight assessment of whether a spot repair or a section rebuild is actually the cheaper path.
Call (844) 343-6681 for a free estimate. A live person answers 24 hours a day, 7 days a week, and we work with a documented roster of brands including Belgard and Unilock for hardscaping, plus KraftMaid, Cambria, and Silestone on the interior side if the same job touches your kitchen or bath.
FAQs

How long do Cover pavers last in Los Angeles? A properly installed Cover paver driveway should hold up 20 to 30 years in our climate. What shortens that is the base, not the paver: shallow compaction, poor drainage, and tree roots near the driveway edge are what fail first in Los Angeles.
Can a failed Cover paver be repaired instead of replaced? Often, yes. A single rocking paver can be lifted, re-bedded, and re-sanded the same day. If the base under a whole section has failed or the edge restraint is broken, a section rebuild is the only repair that holds, and we’ll tell you which one you’re facing.
How long does a paver replacement take? A spot repair runs a few hours. Rebuilding a driveway section including base prep usually takes one to three days, and a full driveway installation runs longer depending on square footage. You’ll get a written timeline before work starts. Call (844) 343-6681 for an exact quote, free.
How do you source the replacement part? We measure your failed unit in all three dimensions and match the Cover series and thickness, then confirm the color lot so it ages in with your existing field. We source to your model’s spec and tell you plainly whether OEM or a quality aftermarket equivalent is the right call for your repair.
Our technicians have up to 22 years of experience, and Bradford Remodeling Co Los Angeles is part of the Garrison Partners family, held to The Garrison Standard: written prices, background-checked and uniformed technicians, and live-person phone coverage around the clock.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












