







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Bufftech Driveway & Pavers: The Los Angeles Owner’s Guide
We install Bufftech-compatible driveway and paver systems across Los Angeles, and paver driveway installation here typically runs $8,260 – $21,240 installed. Pavers themselves aren’t a same-day swap the way a hinge or latch is – a full driveway is a scheduled job – but if a single paver, edge course, or setting bed has failed, small repairs can often be handled in one visit once we’ve matched the profile.
Owners usually find the problem the same way. A paver lifts or rocks under a tire. Sand joints wash out after a rain and the surface starts to look uneven. Or a whole stretch along the apron dips toward the garage, and water pools against the door. In Los Angeles, that pattern is common on older driveways where the base was never compacted to spec. We see it most in the Valley, where summer heat swings and winter rain work the joints hard.
Which Bufftech Models This Applies To

Bufftech is best known for vinyl fencing, and their paver and hardscape lines sit in a different family than the fence systems. That matters because the part that fails is almost never a “Bufftech replacement piece” you order by model number – it’s the paver unit, the edge restraint, the polymeric sand, or the base material underneath. Identify what you actually have before you shop: pull one loose paver and read the stamp or mold mark on the underside, measure it (nominal 4×8, 6×6, 6×9, and 12×12 are the common footprints), and note the color family. Photograph a swept section in daylight.
On the OEM-versus-aftermarket question: Bufftech pavers are made to standard dimension tolerances, so a quality aftermarket paver of the same thickness and footprint will interlock correctly if the color is close. Thickness is the gotcha. A 2⅜-inch paver dropped into a field of 2¾-inch units will sit proud and rock, and no amount of sand fixes it. Measure thickness with a tape, not your eye. If matching exactly, we source through documented brand channels the same way we handle KraftMaid, Cambria, and Silestone specifications – traceable, not guesswork. For edge restraint and polymeric sand, brand match matters less than spec. Los Angeles heat cures sand fast, so the joint-sand grade has to be rated for it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Bufftech Driveway & Pavers Is Failing
- Rocking or loose pavers. A single unit moves underfoot because the setting bed beneath it has settled or washed out. Ignore it and the neighbors start rocking too, since the joint sand that locks them together is already gone there.
- Washed-out joints after rain. Polymeric sand failing at the edges is the first thing we see on Los Angeles driveways with weak edge restraint. Water runs the path of least resistance and pulls the sand with it.
- Ponding against the garage or at the apron. This is a grading or base failure, not a surface problem. It’s the one that turns into a door and threshold issue if it’s left.
- Sunken or heaved sections. In the Valley, clay soil expands and contracts with the wet-dry cycle, and a base that wasn’t compacted in lifts will move. Heaving shows as a hump; settlement shows as a dip.
- Efflorescence – the chalky white haze. Usually moisture working through the slab or base. Sometimes it’s cosmetic; sometimes it signals a drainage problem underneath. Worth a look before you seal over it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s where the numbers land in Los Angeles, and where they come from. Paver driveway installation runs $8,260 – $21,240 installed. Full driveway replacement runs $5,900 – $16,520. Driveway sealing – the maintenance step that protects joints – is $295 – $825. A paver patio, if you’re using the same system out back, is $4,130 – $12,980.
What drives the range: square footage, base depth, whether the old surface has to come out and haul away, edge restraint, and how close the color match has to be on a repair. A one-paver fix sits at the bottom; a full tear-out with a new compacted base and polymeric joints sits at the top. Every quote is line-itemed – pavers, base, edge, sand, labor – written before work starts. No number moves at the door. The work carries our 365-Day Done Right Promise: if it fails within a year, we come back and correct it at no charge.
DIY or Call Us?
You can safely check a lot of this yourself, and we’d rather you did. Lift a loose paver and inspect the base for soft spots. Sweep the surface after a rain and look for where water sits. Measure paver thickness and footprint. Note whether the edge restraint is cracked or pulling away. Those facts make any quote faster and more accurate.
Where DIY goes wrong is the base and the grading. A paver dropped back into a soft bed will fail again in a season, and resetting a settled apron without correcting the slope can send water into the garage or the wall – a much bigger bill than the paver job. Base compaction in lifts and proper fall toward drainage is the part that takes equipment and experience. Most of our technicians have up to 22 years of experience on hardscape and general contracting, and this is the step they see fail most often on DIY repairs. Call (844) 343-6681 and we’ll give you a written price before anyone touches a paver.
FAQs

A properly installed paver driveway with a compacted base typically lasts 25 to 30 years or more, and many run longer. In Los Angeles, the paver units themselves usually outlast the joints and the base – expect to reseal or refresh polymeric sand every few years, more often on exposed driveways in the Valley where UV and heat are hard on the sand. The failure you’re fixing is almost always the base or the joints, not the paver.
Often yes. If the pavers are intact and the base is sound, we can reset loose units, redo the joint sand, and repair edge restraint – a fraction of the cost of a full replacement. If the base has failed over a large area or water is pooling against the structure, a partial or full replacement is the honest answer, and we’ll tell you which one you’re looking at before you commit. Call (844) 343-6681 for a free estimate.
A single-paver repair or joint-sand refresh is typically one visit. A full paver driveway replacement runs a few days to a week depending on square footage, base work, and weather. This isn’t an emergency call – pavers are planned work, and we’ll schedule it properly rather than rush a base that needs to cure and compact correctly.
We match by measurement and spec first, then by color and profile. We work with a documented roster of name-brand materials, including Belgard and Unilock hardscaping alongside KraftMaid, Cambria, and Silestone for interior work, so what goes into your driveway is traceable and warrantied at the manufacturer level. We don’t claim to hold stock of Bufftech parts or carry pavers on a truck – we source the right match for your job.
Bradford Remodeling Co Los Angeles is an independent service provider and is not affiliated with Bufftech.
Ready for a real number? Call Bradford Remodeling Co Los Angeles at (844) 343-6681 for a free estimate. Every price is written before work starts, every job is backed by the 365-Day Done Right Promise, and a live person answers the phone 24 hours a day.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












