







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Home Additions & ADU: The Los Angeles Owner’s Guide
We build and finish Barrette-based home additions and accessory dwelling units in Los Angeles, and the installed cost runs $53,100 – $153,400 for additions and $106,200 – $259,600 for a detached ADU. Every project gets a written price before any work starts and the 365-Day Done Right Promise when we finish. Owners usually come to us after a failure shows up rather than a part number: a plate connection that’s pulled away from the girder strap, a stair ledger that’s started to rock, a window buck that’s twisted after a Santa Ana heat cycle, or a finished addition that won’t hold temperature through a San Fernando Valley summer.
Which Barrette Models This Applies To

The home additions and ADU work we handle in Los Angeles uses Barrette’s structural and exterior build line, which means matching the right component to a specific series and framing run. The way to identify what you have is to find the label or stamp on the original part or on the plan set, then measure the actual opening, span, and plate dimensions in place. Barrette’s ADU and addition components follow their own span and load tables, and a part that looks interchangeable with a generic piece isn’t. A 2×6 ledger strap for a 16-inch on-center wall doesn’t substitute for a 2×8 strap with a deeper embed; a corner post bracket sized for a 4×4 won’t carry a 6×6.
On the OEM-versus-aftermarket question: for structural connections and any component carrying a load path, we use OEM or a qualified equivalent matched to the Barrette spec, because the stamped rating is what your inspector is checking. For non-structural finish hardware, a documented aftermarket part is fine. Bradford Remodeling Co Los Angeles is an independent service provider – not affiliated with Barrette – but we do source and specify Barrette-compatible parts to the plan. If you’re also updating cabinets or surfaces while the addition is open, our roster includes KraftMaid, Cambria, and Silestone.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Barrette Home Additions & ADU Is Failing
- Visible gap at the plate or strap. The connector has pulled off the member it’s fastened to, usually from a load the joint wasn’t designed to hold or fasteners that backed out in a seismic event. In Los Angeles, that’s not cosmetic – it’s the exact failure the connector is there to prevent.
- A stair or landing that rocks underfoot. The ledger or hanger connection has loosened or was undersized from the start. It gets worse with every season’s expansion and contraction.
- Twisted or bowed window and door bucks. A buck that warps after installation is usually the wrong material for the exposed span or a fastener set that didn’t account for thermal movement through hot Valley summers.
- Racking or shudder in a wall that used to be solid. This points to a connection that’s loosened somewhere in the load path, and the first step is finding it, not patching over it.
- An addition that won’t hold temperature. A fully enclosed addition that sweats or runs hot usually has a broken seal or uplifted connector at the envelope, not just a failing HVAC unit.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For context on a full job, a garage conversion runs $35,400 – $94,400 and a home addition runs $53,100 – $153,400. For a targeted part replacement, the installed price depends on the span and how much access the repair needs. That range reflects the labor, the sourced part, the removal of the failed component, and the inspection pass. We give the number in writing before a tool comes out, with no change at the door.
The range moves on whether the load path needs opening up, whether the part is OEM or an equivalent, and how accessible the connection is. Small repair items often fall in the low four figures. A structural rework that touches several connections lands higher, and we’ll say why in the written quote. Every completed repair carries the 365-Day Done Right Promise, so if the same part fails within a year we come back and correct it at no charge.
DIY or Call Us?
An owner can safely do a few things. Look at the visible connections for gaps, missing fasteners, or pulled straps. Photograph the part label so we can cross-check the series and size. Check the plan set for the specified connector. That’s where safe checking ends.
Anything involving a high-tension connector under load, a load-bearing header, or a structural connection inside a wall is not a DIY job. The failure mode is a collapse, and getting it wrong can also mean failing your Los Angeles inspection after you’ve already done the work. A home addition or ADU connects to a whole load path. When one part fails, the fix is figuring out why, not swapping the part and hoping. Call (844) 343-6681 and we’ll tell you what’s actually involved.
FAQs

How long should a Barrette structural connector last in Los Angeles?
A properly matched and installed Barrette connector has no fixed service life – it should last the life of the structure. The real variable is installation and load, not the part. In a coastal climate it lasts as long as the metal holds up, but a failing strap at a plate is almost always an installation or stress issue, not a corrosion issue. Call (844) 343-6681 for an exact quote – estimates are free.
Can this be repaired instead of replaced?
Sometimes, yes. A pulled fastening where the member is intact can often be re-fastened with the correct hardware. A bent or cracked structural connector gets replaced, not straightened. We check whether the cause is still active before we recommend a fix.
How long does the swap take?
A single accessible connector replacement often finishes in under a day. A repair inside a wall of an addition or ADU runs longer because of the access work and the inspection pass.
How do you source the part?
We match the OEM-specified Barrette part or a qualified equivalent to the span and load, then document the spec on the written quote. If a generic substitute won’t meet the load path, we won’t install it.
Call (844) 343-6681 to schedule your free estimate. We give you a written price before any work starts and back the work with the 365-Day Done Right Promise.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












