







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Ameristar Bathroom Remodeling: The Los Angeles Owner’s Guide
Ameristar bathroom remodels in Los Angeles typically install for $10,620 to $33,040, depending on whether you’re updating a hall bath in Mid-City or taking a primary bath down to the studs in Cheviot Hills. Schdeuling a free estimate takes one call, and most projects start within a few weeks of a signed scope – not months. This guide is written for owners replacing builder-grade Ameristar fixtures and finishes installed during the 2000s condo and rental boom, where cheap vanity tops, particleboard cabinet boxes, and low-flow shower valves are now failing fifteen to twenty years in.
Bradford Remodeling Co Los Angeles is an independent contractor. We are not affiliated with Ameristar or any manufacturer listed here.
Key Takeaways
- Typical Los Angeles Ameristar bath replacement: $10,620-$33,040; small baths $5,900-$14,160.
- Every Bradford project gets a written price before tools come out and a 365-Day Done Right Promise on the finished work.
- This is planned construction, not emergency work – we give you a real schedule, not a same-day promise.
- We install KraftMaid, Cambria, Silestone, Kohler, Moen and similar documented brands in place of failing Ameristar components.
Which Ameristar Models This Applies To

Ameristar was a value-tier cabinet and component line built for production builders in Southern California subdivisions and multifamily projects. In a bathroom setting, the “Ameristar” name shows up most often on vanity cabinets, mirrored medicine cabinets, and finish hardware – not on tubs or toilets, which were almost always sourced from other manufacturers. That distinction matters: if you’re chasing a replacement part, confirm what the Ameristar name is actually on before you buy anything.
How to identify what you have. Open the vanity doors and look for a manufacturer label or stamp on the inside of the cabinet side panel or on the back of a drawer box. Measure your cabinet footprint – width, depth, and height – in inches and write it down. Ameristar vanities were commonly sold in 24″, 30″, 36″, and 48″ sizes, but a builder could order nonstandard widths, and a 30-inch vanity from one production run may not line up with the plumbing rough-in from another. Measure the rough-in too: the centerline distance from the drain to the wall.
OEM vs aftermarket. Ameristar is no longer in active production, so a true OEM part is whatever remains in dealer or salvage inventory. For cabinet doors and drawer fronts, a competent cabinet shop can match the profile and finish more reliably than waiting on a discontinued SKU. For the vanity top and faucet – which is what most Los Angeles owners actually want replaced – go aftermarket with a name brand that carries a real manufacturer warranty. That is the honest path, and it’s the one we take.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Ameristar Bathroom Remodeling Is Failing
In Los Angeles, the failure pattern is predictable. Builder-grade particleboard boxes behind a vanity sit against tile and a wall that takes on moisture from shower steam and, closer to the beach, from coastal humidity. Here’s what we see on estimates:
- Swollen cabinet deck or bottom panel. Particleboard wicks water from a slow faucet drip or a leaking supply line and expands, splitting the finish and pushing the doors out of alignment. The cabinet can’t be repaired once the core has swelled; it gets replaced.
- Sagging drawer bottoms under the sink. Ameristar used thin bottom panels with minimal support, and years of stored cleaning products bow them. If the box is still sound, a new drawer box fixes it; if the box itself is sagging, the vanity is due.
- Peeling or separating laminate vanity top. Old laminate lifts at the edge seams, and water gets under the substrate. That’s your cue to replace the top with quartz or another solid surface rather than fight it.
- Scummy, hard-to-clean tile and grout lines. Los Angeles water runs hard, and old grout in an Ameristar-era shower turns chalky and pits. Cracking tiles or soft grout usually mean the waterproofing behind them is gone, which turns a cosmetic job into a shower rebuild.
- Sticking or wobbling shower valve handle. A stiff handle on a two-decade-old valve usually means a worn cartridge or scale buildup in the body. This is a plumbing replacement, not a cosmetic one, and it’s worth doing during the remodel rather than after.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what Ameristar-era bathroom replacement runs in Los Angeles, installed. These are the same ranges we quote across the city, and they include the written price you get before work begins – no numbers that move at the door.
| Full bathroom remodel | $10,620 – $33,040 |
| Small bathroom remodel | $5,900 – $14,160 |
| Bathroom vanity installation | $945 – $3,540 |
| Walk-in shower installation | $5,310 – $14,160 |
| Tub-to-shower conversion | $4,130 – $11,800 |
| Shower replacement | $3,540 – $10,030 |
What drives the range: the condition of the waterproofing behind the old tile, whether the valves and supply lines need replacing, and the finish level you choose. A vanity swap stays low in the range; a full gut with new tile, new valve, and a name-brand cabinet lands near the top.
Every completed project carries our 365-Day Done Right Promise – a written guarantee that if the work fails within the year, we return and correct it at no charge.
DIY or Call Us?
You can safely check and swap the easy pieces yourself: measure the vanity footprint and rough-in, photograph the label, and replace a mirror or faucet. A vanity replacement on good plumbing and a level floor is a weekend job for a careful homeowner.
Where DIY goes wrong: the shower valve and the waterproofing. Touching a shut-off that’s seized, opening a wall around a two-decade-old valve, or re-tiling over failed substrate leads to water damage that costs more than the original remodel. If the wall behind your tile is soft or the grout is failing, that’s a professional call.
Call (844) 343-6681 and a live person answers, any hour – a real estimate, not a callback queue. Estimates are free.
FAQs

How long does an Ameristar vanity or bath component last in Los Angeles? A particleboard vanity in a Los Angeles bathroom typically lasts fifteen to twenty years before moisture swells the box; solid-surface tops outlast the cabinet under them. Hard water shortens grout and valve life across the city.
Can it be repaired instead of replaced? Often, yes – a drawer box, a faucet, or a medicine cabinet door can be repaired. A swollen cabinet core or failed shower waterproofing cannot, and repair there just delays the replacement.
How long does the swap take? A vanity replacement is typically one to two days; a full bathroom remodel runs one to three weeks depending on tile and shower work. We give you a schedule in writing before we start.
How do you source the part? We spec name-brand replacements with manufacturer warranties – KraftMaid or Wellborn cabinetry, Cambria or Silestone surfaces, Kohler or Moen fixtures – so your specifications are documented and traceable, not sourced from salvage.
Every Bradford project is squared away at close: clean site, documented scope, and a signed written guarantee in your hand. Call (844) 343-6681 to schedule your free estimate in Los Angeles.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












