







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Ameristar Driveway & Pavers: The Los Angeles Owner’s Guide
Bradford Remodeling Co Los Angeles installs Ameristar-compatible driveway and pavers throughout Los Angeles, with paver driveway installation running $8,260 – $21,240 installed and paver patio work at $4,130 – $12,980. Most Los Angeles owners discover the failure the same way: a paver edge lifts after a winter rain, a puddle sits in the same spot every storm, or a paver face shears off under a tire. That is usually not the paver material giving up. It is the base under it, the edge restraint holding it, or the joint sand washed out, and each of those is diagnosable on a site visit before anything gets ordered. We’re an independent service provider, not affiliated with Ameristar; we install and correct Ameristar-spec systems and quote the work in writing first.
Which Ameristar Models This Applies To

Ameristar paver profiles show up in Los Angeles on driveways, walkways, patios, and pool decks, and the part that fails reads differently depending on the profile. Knowing which one you have changes what we order and how the repair is built.
- Paver field units: Measure an intact paver face to face, not edge to edge, because the chamfer on Ameristar profiles eats roughly 3/16 in. on each side. A field measurement taken carelessly will make a 6×9 profile look like a 6×12 and you’ll order the wrong unit.
- Edge restraint: The most common weak point. Ameristar installs typically use a plastic or aluminum edge restraint spiked into the base. Los Angeles clay soils shift with seasonal moisture, and a spike loosened by a root or a settled base lets the whole perimeter creep.
- Joint sand and polymeric sand: Joint sand is the material packed between pavers. Once it washes out, water gets under the field units, and a modest rain plus traffic starts rocking them.
- Base aggregate: Class II base or crushed aggregate, compacted in lifts. Undercut base is the reason a flat-looking driveway ruts and ponds after the first heavy storm.
- Geotextile fabric: A separation layer under the base. Skipping it is a silent failure that shows up two or three seasons in.
Please note: we do not stock Ameristar parts and we do not carry parts on a truck. If you need a specific profile matched, we order it, and we confirm the specification with you in writing before ordering so the wrong unit doesn’t get delivered. OEM Ameristar units match the color and dimension of your existing field exactly, which matters on a visible driveway or a patio tied into an existing field. Used or pulled units are cheaper and sometimes available locally, but no two installs fade alike in the Los Angeles sun, and a color mismatch on a front driveway is permanent. If the profile is discontinued, we quote the closest Ameristar equivalent alongside the reconfiguration cost, so the decision stays in your hands.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Ameristar Driveway & Pavers Is Failing
- Paver edges lifting or a puffing at the perimeter. The edge restraint has lost its spike or the base under the perimeter has settled. One lifted corner on a driveway is a warning; the whole perimeter creeping is a base problem.
- Ponding in the same spot every storm. The base was not built to slope. Water sitting against the field units is what washes the joint sand and starts the failure cycle.
- Joint sand washing out after a rain. The joint sand is the shortstop between your pavers and the subgrade. Once it’s gone, the pavers move under traffic.
- Rocking pavers underfoot or under a tire. A paver that rocks means the unit itself is fine and the base under it is not. Replacing the paver without rebuilding the base will just pass the problem to the neighbor paver.
- Pavers that look wet when the rest are dry. Water held in the base moves through the field. If one zone stays damp for hours after a storm, the base is holding water, not draining.
The Los Angeles climate matters here. Most of the metro gets 14 to 16 inches of rain a year, nearly all of it in a handful of winter storms. So a driveway that looks fine for ten months gets tested hard in January and February, and most Ameristar paver failures we see present in late winter or early spring, not summer. Clay-heavy soils from the flats to the hills move with that moisture, and a base built without proper drainage will telegraph that movement straight through the pavers above it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed pricing for the work most Los Angeles Ameristar driveway and paver failures actually need:
| Scope | Installed Range |
|---|---|
| Paver driveway installation (full or rebuilt) | $8,260 – $21,240 |
| Paver patio installation | $4,130 – $12,980 |
What drives the range: square footage, base depth and how much of the old base has to come out, edge restraint selection, drainage correction under the field, and whether the install ties into an existing field that requires a matched Ameristar profile. A spot repair of a handful of pavers and a re-set edge generally lands at the low end; a driveway rebuild with new base, geotextile, edge, and sand sits closer to the top.
Every quote is a written price before any work starts, with the scope of work, the Ameristar profile and finish, and the area measured. Your written price is what you pay at the door. Every completed install carries the 365-Day Done Right Promise: if the work fails inside a full year of completion, we come back and correct it at no charge, and you hold the signed written guarantee at job close along with a clean site and a documented scope.
DIY or Call Us?
You can safely measure. Note the approximate area, photograph the failed section, and check whether an edge restraint is loose or missing at the perimeter. Those details speed up a quote.
Where a homeowner usually gets burned: buying matching Ameristar units without confirming the profile and dimension, then discovering the new field doesn’t match the old one; compacting base in one pass instead of lifts; setting units without proper edge restraint; and re-sanding a joint that should have been rebuilt because the base beneath it has failed. The pavers we pull during a correction are often in good condition, and replacing them alone is the single most common DIY miss we see. If the base, the edge, or the slope is the actual problem, no amount of new paver solves it.
Give us a call at (844) 343-6681 to schedule a free estimate on the Ameristar paver work in Los Angeles. Our technicians have up to 22 years of experience, the crew on your job is background-checked, and a live person answers the phone 24/7 so you’re not leaving a callback behind a queue.
FAQs

The paver units themselves hold up for decades. Ameristar field units are dense, color-through concrete pavers, and in Los Angeles sun and low humidity they should outlast the base under them. The real lifespan is in the base, edge, and joint sand, which is why a well-built Ameristar install can go 20 to 30 years before the field ever needs correction, and a poorly built one can start moving in five.
Yes, on most Ameristar driveways and patios. A lifted edge, washed-out joint sand, or a handful of rocking pavers is a repair, not a replacement: we lift the affected units, correct the base and edge where it’s failed, re-set the pavers, and re-sand. Full replacement is the answer when the base has failed across the field. Call (844) 343-6681 for a free estimate and we’ll tell you which one you actually need.
A paver repair is often a single day on site. A full paver driveway rebuild in Los Angeles typically takes two to four days depending on area, base depth and how much old base has to come out. We give you the schedule in writing with the price so you’re not guessing when the crew will be there.
We confirm the Ameristar profile and dimension first, measure against an intact unit, and order the exact specification before tear-out begins. We do not stock parts, and we don’t carry them on a truck, so we confirm the specification and your written price before ordering, and the Ameristar material is delivered to the job site at the start of the work. Where the profile has been discontinued, we quote the closest Ameristar equivalent and any reconfiguration cost alongside the original spec and let you choose. Call (844) 343-6681 for a free estimate; we also install hardscape from brands like Belgard and Unilock, plus KraftMaid, Cambria, and Silestone for interior work.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












