







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Fence Installation: The Los Angeles Owner’s Guide
A full Barrette fence installation in Los Angeles typically runs $4,130 to $10,620 installed, depending on linear footage, series, gate count, and how much old fence and footing has to come out first. That price covers removal and disposal, new footings set to code, panels, posts, caps, gates, and hardware, plus a written line-item price before anything gets ordered. We’re an independent installer, not affiliated with Barrette, so we quote the actual Barrette-compatible system your property needs rather than a house line.
Owners usually find the problem one of two ways. Either a post has started leaning after a winter of clay soil movement, or a section of vinyl has gone chalky and brittle from five or six summers of Southland UV and the pickets start snapping at the rails. Sometimes it’s simpler: the gate sags, the latch misses, and the whole run suddenly feels loose.
Key Takeaways
- Installed Barrette fence in Los Angeles: $4,130 to $10,620, priced in writing before work starts.
- Clay soil and Santa Ana wind load are the two biggest killers of fence footings here.
- Fully covered by our 365-Day Done Right Promise: if the install fails inside a year, we come back and fix it at no charge.
Which Barrette Models This Applies To

Barrette makes both vinyl and aluminum fence lines, and the part that matters is matching the series, not just the brand. Their vinyl lines run from the value-priced Edgemont and Fairmont families up through the heavy-wall models, while the aluminum side covers the Euro, Solstice and similar ornamental runs. Each series has its own post dimensions, rail profiles and picket spacing. A 5×5 post cap from one line won’t seat on another, and rail ends are not interchangeable.
The fastest way to identify what you have is the post. Measure the outside face of a post: nominal 4×4, 5×5 and heavier posts all read differently, and that measurement narrows the series fast. If a sticker survives on the inside of a rail or on the bottom of a post, read the model code off it. Otherwise look at picket spacing, which varies by line, and the profile of the top rail.
On the OEM-versus-aftermarket question, the honest answer is: match OEM for anything structural. Post caps, gate hardware and rail brackets have aftermarket equivalents that work fine, but posts, rails and pickets should be the same wall thickness and profile as the original or the run will rack and sag differently at the joints. We source the correct part per run and price it as a line item so you can see what you’re paying for.
The same discipline applies across our other trades: we quote KraftMaid and Cambria on kitchens, Silestone on counters, and we treat fence specs the same way. Nothing gets guessed.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Barrette Fence Installation Is Failing
- Posts leaning or rocking after rain. Footings were set too shallow, or the concrete was poured against undisturbed clay that swells and shrinks seasonally. A post that moves by hand is a footing problem, not a post problem.
- Chalking, yellowing, or a white bloom on the vinyl surface. That’s UV breakdown, and it’s normal in Southern California at around the six to ten year mark depending on sun exposure. Once the surface gets chalky, pickets get brittle and crack instead of flexing.
- Pickets snapping at the rail line. Usually wind load combined with aged vinyl or steel rails that have started to corrode inside a hollow post. Santa Ana gusts punish a fence with inadequate post spacing.
- A gate that drags, sags, or won’t latch. Gate hinges and posts take far more load than a straight run. A gate post that wasn’t set deeper or backfilled properly will move first.
- Loose panels that rattle in wind. Rail-to-post connections have worked loose, or the run was installed without the correct insert or bracket for that series. This one usually spreads quickly once it starts.
One more Los Angeles-specific reality: fence runs that border a slope in the hills or sit against a retaining wall see much more soil movement than a flat-lot run. If your property steps, expect footings to need more depth and expect the quote to reflect it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For Los Angeles, a Barrette fence installation or full replacement runs $4,130 to $10,620 installed. That’s the honest spread because footage and site conditions vary widely from a small side-yard run to a full perimeter with two gates.
What drives the number up or down:
- Linear footage and height. A 4-foot side-yard run and a 6-foot perimeter run price very differently per foot.
- Footing conditions. Standard depth in flat yard versus deeper footings for slope, clay, or hardscape removal.
- Gates. A single walk gate and a double drive gate add hardware, heavier posts, and more labor.
- Removal and disposal. Tearing out an old chain-link or wood fence, hauling it, and breaking out concrete footings.
- Permits. Los Angeles has height and location rules for fences, and some runs require a permit. We pull what’s required and pass inspection.
Every project gets a written price before the first post goes in. No numbers that move at the door. The install is covered by the 365-Day Done Right Promise: if the fence fails inside a year, we come back and correct it at no charge.
DIY or Call Us?
Here’s the honest split. You can safely check your own fence by walking the run, pushing each post by hand, looking for chalky or cracked pickets, and confirming gate latch alignment. That tells you what’s wrong. You can order the right replacement part yourself once you’ve identified the series.
Where DIY goes wrong is the installation. Fence footings in Los Angeles clay need proper depth, proper concrete, and the right backfill or the post will move next rainy season. Setting a post plumb and getting a run straight over twenty feet is harder than it looks, and a badly set gate post will sag within a season. Vinyl panels are also unforgiving of a bad cut, so a miscut rail means a wasted part.
Also worth saying plainly: fence work is not the life-safety emergency that a garage door spring or a gas line is, but falling fence panels, leaning posts and a gate that swings into a walkway do cause real injuries. If your run is failing structurally, get it inspected and corrected by a trained crew rather than propped up.
If you want it squared away in writing with a guarantee behind it, call (844) 343-6681. A live person answers, day or night. Free estimates.
FAQs

Expect roughly 15 to 20 years for good-quality vinyl in Southern California, with real caveats. UV exposure in the Southland is the limiting factor: the surface starts chalking around year six to ten, and by year fifteen the material is noticeably more brittle. Post footings and wind exposure matter as much as the vinyl itself, since a fence that goes loose in wind ages quickly.
Often, yes. A single failed post or a few cracked pickets can usually be swapped out if the series is still available and the rest of the run is sound. If more than about a third of the run is showing age or movement, a full replacement usually costs less per year than repeated repairs. We’ll give you the honest read on which is which in writing.
A typical residential run of 100 to 150 feet takes one to three days once materials are on site. Footing cure time and gate installation are the two biggest variables. Los Angeles jobs that need a permit add time on the front end, not the back, so we build that into the schedule before we commit to dates.
We identify the series from the post dimensions, picket spacing and any surviving label, then order the matching component. That may be OEM through a distributor or a quality equivalent that fits the same profile, and we tell you which one you’re getting and why. You’ll see it as a line item on the written quote before we order anything.
Call (844) 343-6681 for a free estimate. We’ll walk the run with you, identify what’s there, and give you a written price before any work begins.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












