







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ViewLux Driveway & Pavers: The Los Angeles Owner’s Guide
We install ViewLux-compatible driveway and paver systems across Los Angeles, and a paver driveway installation here typically runs $8,260 – $21,240 installed, with replacement starting at $5,900 – $16,520 for a full driveway. Most Los Angeles owners don’t notice the hardware failed until a section shifts underfoot, a paver rocks when the car rolls over it, or the joint sand washes out after a hard winter rain. By then the settling underneath has usually been working for a season or two.
That last part matters in this city. Our clay soils expand and contract with the wet-dry cycle, and a 101-degree August afternoon pushes thermal movement through any hardscape that wasn’t built on a properly compacted base. When the base gives, the surface tells you – uneven joints, a lip at the garage apron, sand disappearing into a void.
Key Takeaways
- ViewLux paver and driveway systems we service run $8,260 – $21,240 installed for new installation; a replacement runs $5,900 – $16,520.
- Every job gets a written price before any work starts, and every completed job carries the 365-Day Done Right Promise – if it fails inside that window, we return and correct it at no charge.
- We’re an independent service provider, not affiliated with ViewLux. We source compatible materials to the manufacturer’s published specs.
- A live person answers the phone 24/7 at (844) 343-6681 – no voicemail, no callback queue.
Which ViewLux Models This Applies To

ViewLux’s paver and driveway catalog is built around a handful of paver families with different profiles – a standard 4×8 rectangular, a larger 12×12 or 16×16 slab, and an interlocking profile used for the load-bearing apron where the driveway meets the street. The part that fails isn’t usually the paver itself. It’s the base course, the edge restraint, or the joint sand, and how those pieces are specified changes with the driveway’s traffic load and slope.
Here’s the compatibility gotcha most homeowners miss: a ViewLux paver that matches your surface on paper may not match the thickness of what’s already in the ground. Driveways built to a 2-3/8″ thickness and one built to a 2-3/4″ or 3″ paver behave differently under a loaded car. Where a replacement paver is thinner than the surrounding course, the joint opens within a year and the section starts settling independently. Match thickness to thickness, not just face size to face size.
To identify the right system, look at the manufacturer’s stamp on the underside of an exposed paver or on the bag of joint sand, and measure one full paver’s length, width, and thickness with a tape. Note the colorway, because ViewLux runs face-color variation between production runs and a colorway from a few years back may not read the same as a current batch. For an OEM replacement, that stamp and measurement are what we work from; for a quality aftermarket equivalent, we’re matching to the same spec range and selecting materials with documented manufacturer specs and warranties. We carry no stock of parts and nothing rides on a truck – we source to the job.
The same sourcing discipline applies across the brands we work with, including KraftMaid, Cambria, and Silestone for interior projects.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your ViewLux Driveway & Pavers Is Failing
These are the symptoms we see most often on Los Angeles driveways. Each one points to a different cause underneath.
- Rocking pavers underfoot or under the car. The sand setting bed has washed out or the base course wasn’t compacted to spec, so the paver is sitting on a void instead of bearing on the base.
- Joint sand washing out after rain. A missing edge restraint lets the pavers spread and the joints open. Once water gets in, it accelerates the next failure – a runaway loop.
- A lip at the garage apron or the street transition. The driveway has heaved or settled relative to the fixed concrete. This is the thermal and clay-soil issue in Los Angeles – a hardscaped surface meeting an immovable one.
- Staining or discoloration that won’t wash off. Efflorescence from moisture trapped in the base, or mineral staining from irrigation overspray. Both mean water is moving where it shouldn’t.
- Paver edges chipping or spalling. Freeze-thaw in cold parts of the region, or a paver that was set over an uncompacted base and took point-load stress it wasn’t designed for.
If you see several of these together, the failure is in the base, not the paver. Re-laying the surface over a bad base just buys you the same problem a season later.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here are the numbers we work with in Los Angeles, installed, with labor and materials included:
| Project | Installed Price Range |
|---|---|
| Paver driveway installation | $8,260 – $21,240 |
| Driveway replacement | $5,900 – $16,520 |
| Concrete driveway installation | $5,310 – $14,160 |
| Asphalt driveway paving | $4,130 – $10,620 |
| Driveway sealing | $295 – $825 |
| Paver patio installation | $4,130 – $12,980 |
What moves you along the range: driveway square footage, whether the existing base stays or has to be dug out and rebuilt, the paver profile and thickness, slope and drainage correction, and whether the project is a repair section or a full replacement. A single-section repair near one end of a Los Angeles driveway prices very differently from a full re-lay with a new base and edge restraint.
Parts and labor are quoted line-item and in writing before any work starts. No numbers move at the door. Every completed driveway carries the 365-Day Done Right Promise – a full-year written guarantee, and we return at no charge to correct any failure inside that window.
DIY or Call Us?
A homeowner can safely do a few things to understand what’s happening. Walk the driveway and press on the suspicious pavers to find which ones rock. Check the joint sand depth and look for a missing or broken edge restraint along the sides. Rinse a stained area with water to see if it’s surface dirt or something working up from the base.
Where it goes wrong: if the base has failed, the fix is a base rebuild, and that’s not a homeowner job. It means lifting the full course, digging out and re-compacting the base in lifts, resetting the edge restraint, and re-setting the pavers on a fresh bedding course – with plate compactor work and load grading that has to be right or the new pavers fail on the same schedule as the old ones. Speaking plainly: the part isn’t dangerous the way a spring or a live wire is, but a half-built base is unsafe to drive on, and a springy or rocking surface under a loaded car is a hazard on the road. Leave the base rebuild to the trade.
Call (844) 343-6681 to schedule a free estimate. A live person answers, and you’ll get a written price before we start.
FAQs

A ViewLux paver driveway on a properly built base can hold 20 to 30 years; the paver itself usually outlasts the base and edge restraint, which is where failures start. In Los Angeles, seasonal wet-dry cycling on clay soil is the main force working against the base, so a well-compacted base and a fixed edge restraint are what determine lifespan. Call (844) 343-6681 for an exact quote – estimates are free.
Often yes – if the failure is isolated to one section or one course, we can lift, re-base, and re-set just that portion, which costs far less than a full replacement. If the base has failed across a wide area or the edge restraint is gone, a partial repair won’t hold and replacement is the honest answer. Call (844) 343-6681 for a free estimate and a written scope of what’s actually wrong.
A single-section repair can often be done in one day; a full paver driveway replacement typically takes several days once the base is rebuilt and the pavers are set and joint-sanded. We give you a written schedule with the written price before we start. Call (844) 343-6681 to set up the estimate.
We identify the paver system from the manufacturer’s stamp and a thickness measurement on an exposed paver, then match OEM where available or a quality aftermarket equivalent to the same documented spec range. We carry no stock – every material is sourced to your job and its warranty is documented. Call (844) 343-6681 for a free estimate.
We’re an independent service provider and not affiliated with ViewLux. If your ViewLux driveway is settling, rocking, or losing sand, call Bradford Remodeling Co Los Angeles at (844) 343-6681 for a free estimate. You’ll get a written price before any work starts, background-checked uniformed technicians on the job, and a clean site with your signed 365-Day Done Right Promise in hand at close. A live person answers, 24/7.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












