







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ViewLux Kitchen Remodeling: The Los Angeles Owner’s Guide
We handle ViewLux-based kitchen remodeling in Los Angeles, from cabinet re-facing and full cabinet replacement to countertops, islands, backsplashes and lighting rough-in. Installed projects here typically land between $16,520 and $53,100 depending on scope, cabinet line and surface material. We’re an independent service provider: Bradford Remodeling Co Los Angeles is not affiliated with ViewLux, and we work with your existing ViewLux components or with KraftMaid, Cambria and Silestone when a swap makes more sense.
Most owners discover a problem the same way. A drawer in the ViewLux base cabinet starts dragging halfway out, or a door hangs a few degrees off plum and won’t close flush. You tighten the hinge screws and they spin instead of biting. Under the sink, the cabinet floor softens and the particle board swells. Or a laminate surface lifts at the seam near the dishwasher. In a Los Angeles kitchen, that pattern usually shows up after a dry Santa Ana stretch followed by a wet winter, or after a slow supply-line leak you never saw.
Key Takeaways
- Typical Los Angeles ViewLux kitchen remodel range: $16,520 to $53,100.
- Cabinet installation alone runs $4,720 to $15,340; countertops $2,360 to $7,670.
- Every project gets a written price before any work starts and the 365-Day Done Right Promise.
- Original ViewLux hardware and hinge specs matter; mismatched parts are the most common reason a fix fails twice.
Which ViewLux Models This Applies To

ViewLux cabinetry and surface lines show up in a lot of Los Angeles housing stock, especially condos and mid-size single-family homes built or refreshed between the mid-1990s and the early 2010s. The lines we see most: the ViewLux 100 and 200 series in standard face-frame construction, and the ViewLux 300 and 400 series in full-overlay frameless boxes. The 300/400 frameless boxes use a different hinge bore pattern than the face-frame 100/200 cabinets, and that’s the compatibility gotcha that trips people up. Buying a hinge or drawer slide by cabinet color and door style gets you the wrong part about half the time.
To identify what you actually have, look in three places. Open a door and check the inside of the cabinet side panel for a manufacturer label, usually a sticker or a stamp near the top. Measure the box: frameless ViewLux cabinets are often a true 3/4-inch-thick panel with a 32mm system bore pattern, while face-frame models use a 5/8-inch side panel and a shallower hinge cup. Measure the door thickness too, usually 3/4 inch on both lines but not always. Write down the cabinet width, height and depth in fractions of an inch before you call anyone.
On the OEM-versus-aftermarket call, the decision is simpler than it feels. For hinges, drawer slides and shelf pins, a quality aftermarket equivalent matched to the correct bore pattern works fine and holds up. For a matching cabinet door or a laminate or quartz surface panel, aftermarket matching becomes guesswork, and you’re better off with a documented name-brand replacement than a color approximation. We don’t stock ViewLux parts and don’t carry parts on a truck. We source to the measurement you give us.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your ViewLux Kitchen Remodeling Is Failing
- Doors that won’t stay adjusted. The hinge screws spin because the wood behind them has stripped. This is the first thing to fail on a ViewLux cabinet that has been opened and closed a few thousand times.
- Drawers that drag or jump the track. Slides wear out; the rollers flatten and the under-mount bracket loosens. On a full-overlay ViewLux 300 or 400 box, a loosened slide can also pull the cabinet side out of square.
- A cabinet floor that feels soft or bounces. Particle board above the dishwasher and under the sink swells when it gets wet and never dries back to its original thickness. Left alone, it fails structurally, not cosmetically.
- A laminate or engineered surface lifting at a seam. The adhesive releases along the edge near the dishwasher or a heat source, and water gets under the sheet. Once that happens, patch repairs don’t hold.
- A door or drawer front that’s off square and won’t sit flush. Either the cabinet box has racked, or the door itself has swollen from moisture. In Los Angeles, this usually follows a wet winter in an older kitchen with no working exhaust.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what ViewLux-related and compatible kitchen work runs in the Los Angeles market, installed. These are ranges from real projects, not a call-for-quote placeholder:
- Kitchen remodel, full scope: $16,520 to $53,100
- Small kitchen remodel: $10,620 to $23,600
- Cabinet installation: $4,720 to $15,340
- Countertop installation: $2,360 to $7,670
- Kitchen island installation: $3,540 to $11,800
- Backsplash installation: $945 to $2,950
What drives the range: number of cabinet boxes and doors, whether the frames are face-frame or frameless, surface material (a Cambria or Silestone panel sits above a laminate sheet), and whether the rough-in needs electrical or plumbing moved. Every job gets a written price before any tool comes out, with parts and labor broken out so you can see what you’re paying for. All completed work carries the 365-Day Done Right Promise. If a door doesn’t hang right or a surface seam lifts inside that year, we come back and correct it at no charge. The Garrison Standard is the reason those terms are in writing before we start, not after.
DIY or Call Us?
Some of this is safe to check yourself, and we’d rather you check it than guess. You can tighten a hinge, measure a cabinet box, photograph a manufacturer label, and confirm whether a drawer slide is loose. You can also pull a drawer and look for water damage under a sink.
Where DIY goes wrong: installing a full box, replacing a countertop, and any electrical or plumbing rough-in. A countertop is heavy, and a bad silicone bed or an off-level cabinet top cracks a quartz surface. Moving a supply line under a ViewLux cabinet without shutting the water main is how a small job becomes a flood. If you’ve got a soft cabinet floor or a surface lifting at a seam, you’re past the point a screwdriver fixes. Call (844) 343-6681 to schedule a free estimate and we’ll tell you straight whether you need a repair or a replacement.
FAQs

A ViewLux cabinet box in a normal indoor Los Angeles kitchen typically holds its structure for 15 to 25 years. The surfaces and hardware go first: hinges and slides usually show wear in 8 to 12 years, and laminate seams start to lift sooner if the cabinet is near the dishwasher or under a hot cooktop. Call (844) 343-6681 for an exact quote on whether a repair or replacement makes sense.
Sometimes. A stripped hinge screw is often fixable with a hinge repair plate or a slightly longer screw into solid wood. A loose drawer slide usually needs a new slide, not a new cabinet. But a soft cabinet floor, a racked box, or a laminate sheet lifting at a seam can’t be patched reliably; those need replacement. We’ll tell you which one you have after we see it. Estimates are free.
A single door or hinge replacement is a same-visit job, often under an hour. A drawer slide set is a couple of hours. A full cabinet box or a countertop section is a scheduled project, typically one to three days depending on whether the rough-in has to move. We’ll give you the timeline in writing with the price.
We source to your measurements, not to a guess. You give us the cabinet box dimensions, the bore pattern, the door thickness and the manufacturer label if it’s still there, and we match a compatible part from a documented brand. We don’t stock ViewLux parts and don’t carry them on the truck. If the model is discontinued, we tell you that up front and quote a documented alternative, so you’re never paying for a part that won’t fit. Call (844) 343-6681 for a free estimate.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












