







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Therma-Tru Fence Installation: The Los Angeles Owner’s Guide
We install and service fence systems built around Therma-Tru components, and in Los Angeles the typical installed price for this scope runs $4,130 to $10,620 depending on run length, gate count, and configuration. Most owners don’t realize something has failed until a gate starts dragging the ground, a post leans a few degrees in the rainy season, or a latch stops catching no matter how hard they push it.
The discovery usually comes on a Saturday: you go to swing the side gate shut and it scrapes the concrete, or the picket at the bottom of the run is soft when you press a thumb into it. We’re Bradford Remodeling Co Los Angeles, an independent service provider and not affiliated with Therma-Tru. The sections below cover what fails, what a fair price looks like, and where a homeowner should stop and hand it off.
Which Therma-Tru Models This Applies To

Therma-Tru is best known for door systems, so fence work most often involves their composite and cellular PVC exterior product families – trim, posts, pickets, and hardware that get matched to the door brand. The catch is that these profiles come in specific dimensions: picket thickness is often called out at 5/8″ or 3/4″, posts are cut to nominal 4×4 or 6×6, and the trim cap profiles vary by series. If you’re ordering a replacement section, measure the actual face width of the picket and the inside dimension between posts before you buy anything. A 1/8″ error is the difference between a section that slides in and one that has to be cut down on site.
The OEM versus aftermarket decision matters here. Therma-Tru-spec components exist for a reason: color match, fade resistance, and the way the material takes heat and sun. Aftermarket equivalents can work for a gate frame or a post cap, but we don’t recommend aftermarket pickets in a run that already has Therma-Tru material, because the color drift shows within two summers in Los Angeles sun. If exact color is the priority, stay OEM and wait for the part; if speed matters more than perfect match, a quality aftermarket section is a real option and we’ll tell you which is which before you commit.
To confirm your model, look at the sticker or stamp on the jamb or the injection-molded color plug on the post cap. Measure twice: picket to picket, post to post, and gate width between hinges.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Therma-Tru Fence Installation Is Failing
- Gate drags or won’t latch. The hinges have worn or the post has shifted. Composite gates are heavy, and a hinge set five or more years old will sag before the frame fails.
- Soft or chalky pickets near the base. UV exposure and sprinkler splash drive moisture into the bottom rail. If the material crumbles when you poke it with a key, the section is done.
- Leaning posts. In Los Angeles, the culprit is typically soil movement after heavy winter rain and post footings set in expanding clay. A post that moves 2 degrees in one season will keep moving.
- Loose or missing caps and trim. Wind and thermal cycling pop the adhesive on cap profiles. Once water gets behind the trim, the fastener rusts and the trim separates.
- Color fading or chalky residue on the run. Expected to some degree in Southern California, but an uneven fade pattern on one section points to a mismatched part or a different material batch, not sun damage alone.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For a partial run or single-gate rebuild in Los Angeles, budget $4,130 to $10,620 installed. That covers demolition of the failed section, haul-away, any footing or post-base corrections, replacement material, hardware, and finish trim. Where the price lands depends on run length, whether a gate is involved, whether footings need re-pouring, and whether the surface is set in concrete or soil.
We put the written price down before any work starts – line item by line item, no numbers that move at the door. The work itself is covered by the 365-Day Done Right Promise: if the install fails within that window, we come back and correct it at no charge. Parts and labor are stated separately so you can see what the material costs versus what the work costs.
| Scope | Typical Installed Range (Los Angeles) |
|---|---|
| Single gate rebuild (frame, hinges, latch) | $4,130 – $5,900 |
| Partial run replacement, up to 20 linear feet | $5,900 – $8,260 |
| Full run with post corrections and new gate | $8,260 – $10,620 |
DIY or Call Us?
What you can safely do yourself: measure, photograph the failing section, test the latch, check for soft material with a firm press, and note which post is leaning. That information saves us time and lets us quote accurately before we arrive.
What we don’t recommend for a homeowner: resetting a footing, replacing a hinge set on a heavy composite gate, or re-anchoring a post that’s already shifted. A gate under tension comes down fast when a hinge fails, and a footing poured shallow will lean again within a season. The savings on a DIY reset usually don’t cover the re-do.
Call (844) 343-6681 for a free estimate. A live person answers, 24/7.
FAQs

Expect 15 to 25 years on composite and cellular PVC runs in Southern California, with footings and hardware as the variables that shorten it. UV exposure and soil movement around footings are the two things that age it fastest. Call (844) 343-6681 for an exact quote on your run – estimates are free.
Often yes, if the failure is limited to a gate hinge, a latch, or a single cap or trim piece. Once the picket material softens, a repair buys time but not years. Call (844) 343-6681 and we’ll tell you honestly whether a repair makes sense.
A single gate rebuild typically takes one day; a partial run takes one to two days, weather permitting, and footing corrections add a day for cure time. We schedule the work and put the timeline in writing before we start. Call (844) 343-6681 to get on the schedule.
We work from a documented roster of name-brand materials including Therma-Tru for door and trim systems, KraftMaid and Cambria and Silestone for interior work, so the specification is traceable and material warranties stay intact. We don’t carry parts in a truck; the material is ordered to your measurement. Call (844) 343-6681 for a written estimate.
Ready to get the fence squared away? Call Bradford Remodeling Co Los Angeles at (844) 343-6681 for a free estimate. We give you a written price before any work starts, and every completed job is covered by the 365-Day Done Right Promise. Background-checked, uniformed technicians on every job. Live person on the phone, 24/7.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












