







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Windows & Doors: The Los Angeles Owner’s Guide
We install and replace CGI-compatible windows and doors across Los Angeles, with typical installed windows running $5,310 to $17,700 depending on series, glass package and opening count. If you need a hard-and-fast figure, call (844) 343-6681 and we’ll put a written price in front of you before any work starts. Most owners don’t wake up thinking about CGI window and door parts. They notice a symptom first: a sash that won’t stay up, a door slab that drags on the sill, condensation fogging between panes that won’t clear no matter how warm the afternoon gets. That’s the point where a parts question becomes a real project. Los Angeles homeowners live with year-round sun, dry summers and occasional marine moisture, and the rubber and glass on any window feel every bit of it.
Key Takeaways
- Installed CGI window replacement in Los Angeles typically lands between $5,310 and $17,700; impact-rated glazing pushes higher.
- Match the part to the CGI series and the label on the sash, not the color or the guess in your head.
- Identify the failure before ordering a part: weatherstrip, balance, hardware and glass all fail differently.
- Bradford Remodeling is an independent service provider, not affiliated with CGI.
Which CGI Models This Applies To

CGI is a brand you’ll mostly meet on builder-grade and mid-tier residential work, and the brand has run several series lines over the years. The parts you order depend less on the CGI name than on the series code and the label. So start at the frame: pull back the screen and look for a manufacturer label on the head jamb or the sash edge. That sticker or etched mark usually carries the series identifier, the glass package code and a date. Photograph it before you touch anything. If the label is gone, measure the visible glass width and height, the frame depth and the sill profile and note whether the unit is single or double hung, casement or a door slab.
Then comes the OEM-versus-aftermarket call. For a door slab, hinge set or a specific weatherstrip profile, OEM is the safe answer because the tolerances are tight. For balances, rollers and sash locks, a quality aftermarket equivalent that matches the dimensions works fine and costs less. A common gotcha with CGI units: the glazing bead and the balance shoe changed profile across series, so a part that fits one year’s window can be a loose or jammed fit on the next. Measure, don’t assume, and if you’re unsure, ask us and we’ll help you identify the right piece before you order. Los Angeles homes built in different decades carry different CGI lines, and the address alone won’t tell you which.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Windows & Doors Is Failing
Here’s how a CGI window or door usually tells you it’s done. Each symptom points at a different part, which is why the repair bill depends on an accurate diagnosis.
- Sash won’t stay open. The balance has lost tension or the balance shoe has snapped; it’s a mechanical part failure, not a glass problem.
- Condensation or a milky haze between the panes. The insulated glass seal has failed, letting moisture into the air gap; no amount of wiping fixes the glass, only replacement does.
- Door drags or won’t latch square. A hinge worn or a slab that has settled as the frame moved with the seasons; sometimes the hardware, sometimes the opening.
- Draft or whistle at the edges. Weatherstrip flattened out or cracked, or the sash no longer seals against the frame; it lets hot Southland air straight in.
- Lock or crank hard to turn. Corrosion and grit inside the hardware after years of dry dust and sun exposure; the operator may be binding or the mechanism is worn.
What fails first has a lot to do with where the window sits. On the east and west elevations, sun exposure shortens the life of rubber seals and any plastic hardware. On coastal edges, salt air and marine moisture speed up metal corrosion. A Los Angeles homeowner with a CGI unit facing open sun will see weatherstrip go before the glass; one shaded in a courtyard may last longer on the seals and fail on the balance instead. Someone with a sliding glass door on a south wall is watching rollers wear a little sooner than they’d like.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s the honest picture. A single window’s part-plus-labor often costs less than a full unit swap, but once the glass seal fails or the frame is out of square, a whole-unit replacement is the cheaper path over time. Our Los Angeles installed pricing:
| Scope | Installed Range |
|---|---|
| Window replacement (single/double hung, casement) | $5,310 – $17,700 |
| Impact-rated window installation | $9,440 – $29,500 |
What drives the range: window size, glass package, frame material, number of openings and whether trim or stucco repair is needed. A hard-to-reach second-story opening adds labor. We write the parts-and-labor price down before any work starts; there are no numbers that move at the door. Every completed install carries our 365-Day Done Right Promise: a full-year written guarantee, and if the work fails inside that window, we come back and correct it at no charge. You’ll have the signed guarantee in your hand at close, along with a clean site.
DIY or Call Us?
Some things you can safely check. Open and close each sash, watch the balance, feel the weatherstrip for cracks, clean the track and look for a label. On a door, tighten a loose hinge screw and see if the drag clears. A sticking lock or a sluggish crank is often a simple hardware swap. That’s where the safe line sits. Windows and doors involve high-tension balances, heavy glass and openings that can go out of square quickly if you force a fit. If the sash won’t seat or the glass seal is blown, the smart call is to have it looked at, not to wrestle it in yourself. Call (844) 343-6681 and we’ll tell you whether the fix is a part or a unit, and what it will cost. Estimates are free, no pressure.
FAQs

Expect roughly 15 to 25 years for the unit itself, with weatherstrip and hardware wearing out sooner under direct sun or coastal salt air. A blown glass seal often shows up well before the frame does. Call (844) 343-6681 for an honest read on whether to repair or replace your Los Angeles window.
Yes, if the frame and glass are sound and the failure is a balance, weatherstrip, roller or lock. Once the insulated glass seal fails or the frame is out of square, replacement usually costs less over time. We’ll tell you which side of that line you’re on, free of charge.
A single window or door replacement is typically a one-day job for a standard opening; multiple units or impact-rated glazing can take longer. A same-day installation is sometimes possible when the part is a direct fit and the opening is ready. Call (844) 343-6681 and we’ll give you a realistic timeline, not a guess.
We identify the CGI series from the label or the measurements and order the right part within a documented roster of brands, not off a guess. That means the spec is traceable, so the fit is right the first time. Bradford Remodeling is an independent service provider and is not affiliated with CGI. We also service KraftMaid, Cambria and Silestone products in the same disciplined way: written price, no surprises, and the 365-Day Done Right Promise behind the work.
Ready to get your CGI window or door squared away? Call Bradford Remodeling Co Los Angeles at (844) 343-6681 for a free estimate. We’ll put a written price in front of you, answer the phone with a real person 24 hours a day, and send background-checked, uniformed technicians to your door. Our technicians have up to 22 years of experience, and every install is backed by our full-year written guarantee.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












