







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Bathroom Remodeling: The Los Angeles Owner’s Guide
Bathroom remodeling built around Tamko products in Los Angeles typically runs $10,620 to $33,040 installed, with the high end covering a full tear-out, new shower pan, waterproofing, tile, vanity, and fixtures. Smaller refreshes land under $14,000. Most Los Angeles owners start noticing a problem the same way: a soft spot along the shower curb, a grout line that keeps opening, or caulk that peels back within weeks no matter how many times it gets redone. Those are early signs that the waterproofing layer under the tile – not the tile itself – is letting water through. Bradford Remodeling Co Los Angeles installs Tamko-compatible bathroom systems and works with KraftMaid, Cambria, and Silestone for cabinetry and surface finishes. We are an independent service provider and are not affiliated with Tamko.
Which Tamko Models This Applies To

Tamko makes several waterproofing and underlayment products used under bathroom tile, including sheet membranes and liquid-applied membranes. Matching the right one depends on what’s already under the floor or wall, not just the label on the box. Tamko sheet membranes are commonly specified in 30-inch and 39-inch roll widths, and liquid membranes have specific cure windows before tile goes down. A membrane laid over greenboard or over unmodified thinset cures differently than one set over modified thinset, and that mismatch is one of the most common failure points we find in Los Angeles homes.
How to identify what you have
Pull the manufacturer label off the membrane or the box, photograph it, and note the roll width if it’s stamped on the edge. If the label is gone, an installer can read the membrane by texture and thickness – a waterproof sheet has a distinct fleece backing and typically measures 8 to 30 mils thick. Write down the room dimensions and where the shower valve and drain are.
OEM vs. aftermarket – the honest call
For a waterproofing membrane, matching the exact Tamko system matters more than it does for, say, a vanity faucet. A membrane is only part of a warranty-backed system – the drain flange, corner pieces, and banding all have to come from the same family. Aftermarket drain fittings that don’t match the flange height will leak at the joints. In Los Angeles, our recommendation is to stay with the specified system and let a trained installer set it. Labor is the larger cost, and calling back a failed waterproofing job costs more than the membrane ever did.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tamko Bathroom Remodeling Is Failing
- Grout that opens in straight lines along the shower floor. Movement in the substrate below, not just grout shrinkage. That usually means the membrane wasn’t set correctly or the substrate was under-specified.
- Caulk peeling at the shower-to-floor seam within three months. A sign of moisture behind the membrane, not a caulk problem. Re-caulking hides it for a few weeks at most.
- A soft or spongy spot along the shower curb or curb corners. Water is sitting in the curb structure. This is the single most common call we get in Los Angeles, and it usually traces back to a corner piece that wasn’t bonded with the right adhesive.
- Musty smell that returns after cleaning. Water is in the wall cavity or under the pan. Musty odors inside a bathroom belong to moisture behind the finish.
- Lifting tile around the drain flange. The drain collar wasn’t set tight against the membrane, so water runs behind it. Tile pulls loose within a year or two.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed pricing for Los Angeles bathroom remodeling with a Tamko waterproofing system:
| Scope | Installed Price Range |
|---|---|
| Bathroom remodel (full) | $10,620 – $33,040 |
| Small bathroom remodel | $5,900 – $14,160 |
| Walk-in shower installation | $5,310 – $14,160 |
| Tub-to-shower conversion | $4,130 – $11,800 |
| Shower replacement | $3,540 – $10,030 |
| Bathroom vanity installation | $945 – $3,540 |
The range depends on tile size, whether the substrate needs replacement, plumbing relocation, and whether a permit is required – most Los Angeles bathrooms do trigger a plumbing permit for fixture relocation. Parts and labor are quoted line by line. Every completed project carries the 365-Day Done Right Promise: if the work fails within a year, we come back and correct it at no charge. Written price before any tool comes out.
DIY or Call Us?
A homeowner can safely check the caulk lines, look for soft spots along the curb, and photograph the label on the membrane. Anything deeper – lifting tile, cutting out the shower pan, opening the wall behind the valve – is where it goes wrong. Waterproofing fails in layers, and a failed membrane doesn’t show you the leak until the damage is behind the wall or under the floor. On a Los Angeles bathroom, a mistake in that layer usually costs more to correct than installing it correctly the first time.
The membrane itself is not dangerous to handle, but the removal and reinstallation involve cutting into walls, working with drain flanges, and disturbing plumbing – work that has to be done with the water shut off and the permit in place. Call us at (844) 343-6681 to schedule a free estimate. A live person answers 24/7.
FAQs

Fifteen to twenty-five years is the normal range when the membrane is set over a stable substrate and the seams are bonded correctly. In Los Angeles, the biggest lifespan shortener is ground movement from seasonal soil shrink, which flexes the shower pan and opens membrane seams. A properly sloped pan and a bonded corner piece are the two things that make the difference.
Sometimes. If the failure is limited to a specific seam or the drain collar, a targeted repair is possible and typically costs $470 to $2,125. If the substrate is soft or tile is lifting more than a square foot, a partial repair won’t hold. We inspect the substrate and give you a written recommendation either way. Call (844) 343-6681 and we’ll tell you which side of that line you’re on.
A shower replacement runs three to five working days for most Los Angeles bathrooms. Tile setting and membrane cure add time – the membrane needs to cure fully before tile goes on, so rushing it defeats the whole point. Full bathroom remodels run two to four weeks depending on finishes.
We specify the membrane system by manufacturer and model, and we install it exactly as the manufacturer’s installation instructions specify. That keeps the system in one family – membrane, drain flange, corner pieces, banding – so the warranty terms apply cleanly. Because we’re not affiliated with Tamko, we install Tamko-compatible products alongside KraftMaid, Cambria, and Silestone finishes as the specification calls for. Every job gets a written price before work begins.
Call (844) 343-6681 for a free estimate. We answer live, 24/7. You’ll have a written price before a single tool comes out.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












