A Bradford company - serving Los Angeles, CA
A remodeled primary bathroom with a soaking tub and a walk-in shower
Schluter · Los Angeles

Schluter Roofing in Los Angeles, CA

Free Estimate on SiteCalls Answered by a Live Person, 24/7Background-Checked TechniciansA Local Team in Los Angeles
A walk-in shower with large-format tile and a built-in niche
A remodeled hall bathroom with subway tile and a floating vanity
A remodeled hall bathroom with patterned floor tile and painted walls
A low-threshold walk-in shower with a bench and grab bar
A powder room with botanical wallpaper and a stone sink
A home office with a built-in desk and shelves
A remodeled kitchen with a waterfall island and wood cabinets
An open living space after a whole-home remodel
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Schluter Roofing: The Los Angeles Owner’s Guide

If you’ve found a cracked, clogged, or separated Schluter roof component, you’re likely looking at an installed replacement cost of $470 – $2,125 for a repair and $9,440 – $23,600 for a full roof replacement, depending on scope. Our technicians have up to 22 years of experience and treat Schluter products as what they are: a high-end tile and stone roofing system where a failed edge profile, drainage mat, or edge termination can quietly funnel water under your field tile long before you see it inside. Most Los Angeles owners discover the problem the same way. A stain creeps across a ceiling in the valley of an A-frame, tile edges look lifted after a Santa Ana wind event, or a contractor doing a bathroom remodel upstairs mentions the roof deck feels soft near the eaves. We’re an independent service provider and not affiliated with Schluter, so we source compatible parts by specification, give you a written price before work starts, and back the repair with the 365-Day Done Right Promise.

Call (844) 343-6681

Which Schluter Models This Applies To

A tile setter installing wall tile in a shower

Schluter’s roofing line centers on a few product families: the KERDI-DRAIN and KERDI-LINE linear drainage mats, SCHIENE and RONDEC edge profiles used as tile terminations, TREP-E, TREP-V, and TREP-G stair-nosing profiles at transitions, and KERDI-BOARD panels used as substrate where it applies. Each profile shares a naming convention that tells you the leg depth and the finish, so a SCHIENE 8mm satin anodized aluminum is not interchangeable with a 10mm version or with the brushed-finish equivalent. The label is almost always stamped or printed on the protective plastic film; if that film is gone, measure the visible leg height with a tape to the nearest millimeter and measure the overall length before you order anything.

Here’s the OEM-versus-aftermarket call you’ll face. Schluter-brand replacements are worth ordering when the profile is visible and exposed to weather, because the finish and the material spec are part of what you paid for. Equivalent anodized aluminum and stainless profiles from reputable manufacturers exist and fit the same slot when the piece is under a tile reveal or tucked behind a termination bar and finish match isn’t cosmetic. What we don’t do is mix brands within a single run of edge termination, because dimensional differences of a millimeter or two can mean a loose mechanical hold. We do work with KraftMaid, Cambria, and Silestone on the interior side, and we bring the same documented-spec approach to roofing parts sourcing.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Schluter Roofing Is Failing

Schluter systems are supposed to drain water and terminate tile cleanly. When they don’t, the failure is almost never the piece itself failing structurally; it’s the piece losing its seal at a joint, clogging, or separating from the substrate.

  • Visible cracking or crazing on the profile face. UV exposure and the Los Angeles sun age the finish and the aluminum oxide coating faster than most owners expect, usually in the 12-18 year range on a south-facing slope. A hairline crack in a SCHIENE face lets water behind the profile.
  • Lifted tile edges sitting over the profile. If tile is sitting up on one side of the linear drain or edge termination, the thinset bond broke, usually after thermal cycling or a heavy wind event. The profile is still there but no longer holding the tile tight.
  • Water pooling at the drain mat or linear drain. Debris, asphalt shingle granules, and California ash buildup from wildfire seasons clog the drainage pattern. Water backs up under the field tile and starts showing as a dark stripe on stucco within 6-10 feet.
  • Rust or white oxidation streaks below the profile. Aluminum and stainless components oxidize differently. White streaking on a stainless KERDI-LINE grate means it’s been sitting in wet debris; rust streaks on an aluminum profile mean the finish is compromised.
  • Soft spot in the roof deck or substrate near the transition. This is the one that matters most. A leak that has been running for a season or two softens the deck beneath the KERDI-BOARD panel, and the repair scope grows from a part swap into a substrate replacement.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

A finished backyard cottage with a small covered porch

For Los Angeles, the installed price on a Schluter roofing repair runs $470 – $2,125 for a scope that includes removing the failed profile or drain mat, replacing it with a compatible part, re-flashing or re-terminating, and a water test. A full roof replacement, when the failure has spread into the deck and the field tile, runs $9,440 – $23,600. A tile roof repair on its own runs $710 – $2,950. Metal roof installation, when the whole system goes that direction, is $17,700 – $47,200.

Three things drive where you land in that range: how much of the substrate is wet, how many linear feet of the profile needs replacing, and whether the matching finish and mill spec are still being made in the width you have. The written price covers the part, the labor, the flashing, the disposal, and the water test. Parts and labor are line-itemed separately so you can see exactly what a Schluter-brand replacement costs versus the equivalent aftermarket. If we open the job and find the deck is softer than the written scope assumed, we stop, we show you, we write a new number, and we do not move one screw until you approve it. That’s The Garrison Standard in practice. Every completed repair carries the 365-Day Done Right Promise: if it fails inside the year, we come back and correct it at no charge.

DIY or Call Us?

You can safely get on a ladder to inspect, photograph, and measure. Check the profile from the ground with binoculars for cracks and lifted edges, note the length and leg-depth measurement, and look at the underside of the deck from inside an attic or soffit vent for a soft spot or moisture discoloration. That inspection doesn’t require tools and it’s worth doing before you call anyone.

Where DIY goes wrong is on the roof itself. Roof work on a pitched surface, especially at the eaves and around valley transitions, is fall-risk work. One slip on a 6/12 pitch or a wet tile and the day ends very differently than planned. Beyond the fall risk, the failure most owners introduce on a DIY Schluter repair is a termination that looks right and isn’t: the profile is pressed flat but the sill seal behind it is too thin, or the profile is trimmed with a grinder and a burr sits inside the drainage channel where you can’t see it. The water test at the end is what tells you it worked, and that’s the step people skip. Call (844) 343-6681 and we’ll schedule a free estimate with a live person on the other end. We give you the written price before work starts, no numbers that move at the door.

FAQs

A remodeled living room with built-in shelves around the fireplace

How long does a Schluter roofing profile last in Los Angeles? Expect 12-20 years on the finish and the profile body, depending on sun exposure and how well the drainage path is kept clear. South- and west-facing slopes in Los Angeles face the strongest UV load and often reach the shorter end of that range. Call (844) 343-6681 for an exact quote on a replacement; estimates are free.

Can I repair the Schluter component instead of replacing it? Sometimes. A clogged KERDI-LINE drain mat, a single separated profile section, or a re-terminated edge can often be repaired rather than replaced, and that’s a $470 – $2,125 job rather than a full replacement. A profile that has cracked through its body, or a substrate that’s gone soft, needs to be replaced. Call (844) 343-6681 and we’ll tell you honestly which side of that line you’re on after an inspection.

How long does a Schluter roofing repair take? A single-profile swap at a roof edge is a half-day to one-day job once the part is on site. A linear drain mat replacement with re-flashing runs 1-2 days. The longer lead time is usually sourcing the part in the right finish and mill spec; we order by the exact specification, not the closest available, and we don’t quote a date until the part is confirmed.

How do you source the part? We source Schutler-compatible parts by the measurements you give us, or the measurements we take ourselves during the estimate: leg depth, overall length, material, and finish. If the original spec is discontinued we propose a documented equivalent and explain the trade-off. We don’t carry parts on a truck and we don’t stock Schluter locally, so the part is ordered to the job. Written price before work begins, every time. Call (844) 343-6681 to set up the estimate.

Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.

Ideas for every room in the house

Built-ins, window seats, family rooms and staircases: the changes that make a whole house work better.

Read our remodeling guides
A remodeled family room with new windows and a window seatA wide opening with a new beam where the kitchen wall was removedA small remodeled galley kitchen with cabinets to the ceilingA finished basement family room with a media wall and wet barA walk-in pantry with wood shelvingA remodeled laundry and mudroom with a bench, cubbies and painted cabinets

Explore more remodels

Every project below starts the same way: a free on-site visit and a written price.

Getting started with Bradford in Los Angeles

Every project starts with a conversation and a written price. Here is how to take the first step.

A project lead measuring a kitchen with the homeowner during a free estimate

Free on-site estimate

A project lead walks the job with you, measures it and hands you a written, line-item price. No obligation.

Book an estimate
A remodeling crew arriving at a home with lumber and tools

Your Los Angeles team

A local vetted partner works across Los Angeles and the towns around it, to the same written standard as every Bradford job.

Areas we serve
A worker laying floor protection and a dust barrier before work starts

Read our written promise

What we promise on every job, written down, with the terms spelled out before any work starts.

Our promise
Need Construction help nationwide? Licensed & insured · free written estimates
Call (844) 343-6681
Local Service Coverage

Request a Free Estimate in Los Angeles

Tell us what you need - Bradford Remodeling Co Los Angeles responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch