







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Kitchen Remodeling in Los Angeles: The Owner’s Guide to Failed and Failing Schluter Systems
Schluter kitchen remodeling in Los Angeles typically runs $16,520 to $53,100 installed, and most of that work is stone, tile and surface installation over Schluter’s waterproofing and uncoupling systems, not the membrane itself. When a Schluter component fails under a kitchen floor or backsplash, you usually find out through a cracked tile, a soft grout line or a membrane edge lifting at a cabinet toe kick. We install Schluter systems to manufacturer spec, give you a written price before work starts, and back the result with our 365-Day Done Right Promise.
Bradford Remodeling Co Los Angeles is an independent remodeling contractor. We’re not affiliated with Schluter Systems, and we don’t sell parts or keep any stock on hand. What we do is install and repair the assemblies those parts go into, correctly, throughout Los Angeles.
Key Takeaways
- Schluter failures in Los Angeles kitchens are almost always installation errors, not product defects.
- A single cracked tile over a loose membrane rarely means one bad tile. It usually means the whole bed needs to come up.
- We quote installed pricing in writing before any demolition, not a per-square-foot guess.
- Every completed repair or remodel carries a full-year written guarantee.
Which Schluter Models This Applies To

Schluter makes several product families that show up under a Los Angeles kitchen, and each one fails differently. Knowing which you have changes the repair scope and the price.
DITRA and DITRA-HEAT. DITRA is the uncoupling membrane; DITRA-HEAT adds a heating cable grid. The flanged edge of the sheet is the weak point. If it wasn’t overlapped and sealed per the manufacturer’s instructions, thinset bleeds into the channel and the tile above debonds within a few seasons.
KERDI and KERDI-BAND. Waterproofing for backsplashes and wet zones. KERDI-BAND seals the seams. A missed seam or a band installed without the correct thin-set mortars shows up as efflorescence or dark grout lines near the sink.
SCHIENE and JOLLY. Edge profiles in aluminum, PVC and stainless. The most common replacement need, usually because the profile was cut short at a cabinet or the anchoring leg was too thin for the tile.
How to identify what you have. Pull the manufacturer’s spec sheet from the box or look for the printed membrane logo on any exposed edge. Measure sheet thickness. DITRA runs about 1/8 inch; a thicker sheet signifies a different system. Match your tile size to the membrane’s minimum tile requirement before you buy anything. DITRA specifically requires tiles no smaller than 2 x 2 inches over it, a spec homeowners routinely miss. If you have a mosaic backsplash, that membrane is the wrong product for the job.
OEM Schluter parts are the only ones we’d specify for a warranty-backed install. The systems rely on exacting thin-set contact and overlap dimensions, and aftermarket membranes that claim to match don’t carry the same tested assembly data. For a repair over a small area you may find close equivalents at a Los Angeles tile supplier, but the assembly won’t be covered the same way.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Kitchen Remodeling System Is Failing
- Hollow-sounding tiles underfoot. Tap a coin across the floor. A dull thud means the bond between tile, thin-set and membrane has broken. Usually caused by thinset that skimmed over before the tile went down.
- Cracked grout lines running in straight lines. Cracks that follow tile joints rather than random patterns point to movement the uncoupling membrane was supposed to absorb and didn’t, often because the subfloor deflected beyond spec.
- Lifted or curling membrane edges at a cabinet toe kick. The overlap wasn’t fully embedded. Moisture gets behind the sheet and the edge peels back slowly, a gradual failure you notice months later.
- Dark or powdery grout at the backsplash near the sink. Efflorescence or a wet grout line signals a KERDI seam that was never properly banded. Left alone, water reaches the drywall behind it.
- Loose edge profile at a countertop or exposed tile edge. The anchoring leg was cut too narrow, so the profile works loose as the tile expands and contracts with seasonal heat.
Los Angeles doesn’t get the freeze-thaw cycles that break tile in colder states, but our dry inland heat and the seasonal swing from a cool coastal morning to a 95-degree afternoon in the Valley move tile assemblies constantly. That’s why we see more uncoupling failures in kitchens in the San Fernando Valley and the Santa Clarita corridor than we do on the Westside, where the ocean moderates the temperature swing.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what the work costs in Los Angeles, installed, with the parts, thin-set, setting materials and labor included:
| Scope | Installed Price (Los Angeles) |
|---|---|
| Kitchen remodel (full) | $16,520 – $53,100 |
| Small kitchen remodel | $10,620 – $23,600 |
| Cabinet installation | $4,720 – $15,340 |
| Countertop installation | $2,360 – $7,670 |
| Backsplash installation | $945 – $2,950 |
| Kitchen island installation | $3,540 – $11,800 |
What moves the range up or down: the square footage, whether the existing tile and thin-set need full demolition, whether the substrate is sound or needs a new layer of plywood or cement board, and the tile or stone selected. Repairs confined to a backsplash or a small floor area land near the low end. Full kitchen remodel scopes that include cabinets and countertops over a new Schluter floor system land near the high end.
We write the price down before work starts. That quote itemizes materials and labor separately, and it does not change because something unexpected turns up after demo unless we sit down and revise it with you in writing first. When the job closes, you get a squared-away site, a documented scope, and a signed written guarantee in your hand. If the work fails inside that window, we return and correct it at no charge.
DIY or Call Us?
Some of this is safe to check yourself, and some of it isn’t worth the risk.
What you can safely check. Tap the floor to map hollow spots. Run a level across a tile joint. Look for band seams under a sink cabinet. Photograph the exposed membrane edge so we can identify the product family before we quote. None of that puts you on your knees with a chisel.
Where DIY goes wrong. Pulling a single tile to inspect the membrane often takes the adjacent tiles with it. Chipping a tile up from a Schluter system risks cracking the surrounding field. Lifting a small tile on a shower or wet-zone floor can open a path for water behind it. The safest move is to stop and get a pro to look before you swing a chisel.
Repairs and remodels here are planned work, not emergencies. Call us to schedule an estimate at (844) 343-6681. A live person answers the phone, day or night.
FAQs

A correctly installed Schluter system should outlast the tile over it, often 15 to 25 years or more. The membrane itself doesn’t wear out. The failure is nearly always an installation error (wrong thin-set, a missed overlap, or a subfloor that wasn’t stiff enough), and that shows up within one to five years. Call (844) 343-6681 if you suspect a failure, and we’ll come look.
Small repairs are possible when the failure is isolated to one area and you caught it early, such as a single loose profile or a small section of lifted membrane at a toe kick. A cracked field of tiles over a debonded membrane usually means pulling the affected area back to sound substrate and rebuilding it. Call (844) 343-6681 for a written quote before anyone commits.
A single profile swap or a small membrane repair is a few hours to a full day, including cure time. A backsplash rebuild runs two to four days. A full kitchen floor rebuild with a new Schluter system runs one to three weeks depending on square footage and how much demolition the existing tile requires. Call (844) 343-6681 and we’ll give you a firm timeline in writing before work starts.
We source Schluter products and setting materials through supply houses that carry the manufacturer’s tested assembly data, then match the part to your exact model, sheet thickness and tile size. We don’t stock parts or carry inventory in a vehicle. Before we order anything, we confirm the product family and the minimum tile requirement so the assembly is right the first time. Call (844) 343-6681 to get a written price and a documented material list.
If you’re considering new cabinetry or surfaces over your Schluter system, we also install KraftMaid, Cambria and Silestone, among other documented brands. A free estimate covers the whole scope and puts the price in writing before any tool comes out. Call (844) 343-6681 to get on the schedule.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












