







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Silestone Driveway & Pavers: The Los Angeles Owner’s Guide
We install Silestone-compatible driveway and paver assemblies across Los Angeles, and the numbers run $8,260 to $21,240 for a paver driveway, with pavers laid over a properly compacted substrate. A Silestone paver system doesn’t have a motor or a spring, so what usually fails is the base under it: a settled subgrade, a cracked slab edge, or grout lines that open up after a wet winter. Homeowners in Los Angeles tend to notice it first as a driveway paver that rocks when the car rolls over it, or a hairline crack that shows up every spring in the same three feet of the apron.
Because this is a surface-and-substrate job rather than a mechanical part, the real question isn’t “which part do I order” but “what’s underneath it, how thick, and does it match the Silestone system that’s already down.” We measure, quote it in writing, and tell you whether you’re looking at a repair or a full lift and relay.
Key Takeaways:
- Paver driveway installation in Los Angeles: $8,260 – $21,240 installed.
- Most failures are substrate, not surface: settle, drainage, or edge restraint.
- You get a written price before any work starts, and the 365-Day Done Right Promise covers the installation for a full year.
Which Silestone Models This Applies To

Silestone pavers and driveway systems come in series that differ by thickness, edge profile, and finish, and the part number you need depends on which series is already installed. Silestone is a quartz-based surface, and its outdoor paver lines are typically specified at 2 cm or 3 cm thickness depending on whether the application is a driveway (load-bearing, so thicker) or a walkway and patio. That thickness is the first compatibility gotcha: a 2 cm paver rated for foot traffic is not the same product as a 3 cm driveway paver, and mixing the two across a single field is how you get a joint that fails within a year.
To identify what you have, check the install documentation if the previous owner kept it, then look for a stamp or label on the underside or edge of a loose paver. If there’s no label, measure the thickness with a tape and note the color name and finish, because Silestone color lines don’t share a dye lot across production runs and a replacement paver from a different batch can read slightly off next to the existing field. That’s the OEM-versus-aftermarket decision here: for a repair, sourcing a matched Silestone paver from the same line is worth the wait, because an unmatched substitute will be visible from the sidewalk. For a full relay, you have more room, and we can spec a current Silestone paver line with documented manufacturer specs behind it.
We also work with KraftMaid, Cambria, and Kohler on the interior side, so if the driveway project turns into a front-entry refresh, the same written-price process applies.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Silestone Driveway & Pavers Is Failing
- Pavers that rock or sound hollow when you walk on them. That’s a loss of bedding sand or a settled subgrade under the paver, not the paver itself failing. Left alone, the rocking edge chips and the joint opens.
- Grout or joint sand washing out after rain. In Los Angeles, our short heavy rain events push water through a joint that wasn’t compacted correctly, and once the sand is gone the pavers shift.
- Heaving or a lip where the driveway meets the apron or garage slab. Often a drainage or edge-restraint problem – the pavers have nowhere to push against, so the field creeps.
- Cracks that run in a straight line across several pavers. Straight-line cracking usually traces to a slab or base joint underneath, which means the repair is at the substrate level, not a surface patch.
- Staining or color change in one section. Standing water under the pavers wicks up and discolors the surface, and in our climate that’s usually a grading issue rather than a cleaning issue.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

In Los Angeles, a paver driveway installation runs $8,260 – $21,240 installed. A paver patio installation runs $4,130 – $12,980. A driveway replacement, meaning tear-out of the old surface and rebuild, runs $5,900 – $16,520. Driveway sealing, when the pavers are sound and just need protection, runs $295 – $825.
What drives the range: square footage, whether the base has to be excavated and recompacted, edge restraint and drainage work, and how much of the existing field gets salvaged. We quote parts and labor separately so you can see what a matched Silestone paver costs versus the base work underneath it. Every one of these jobs gets a written price before a single tool comes out, with no numbers that move at the door, and the finished installation carries the 365-Day Done Right Promise – if the work fails inside that year, we come back and correct it at no charge.
DIY or Call Us?
You can safely check a few things yourself: walk the field and note which pavers rock, measure thickness at an exposed edge, photograph the joint lines after a rain, and check whether water pools toward the house or the garage. What we’d steer you away from is lifting and relaying a section over an existing base without knowing what’s under it, because a paver field is a system – base, bedding, paver, joint, restraint – and fixing the top layer over a bad base is how homeowners end up doing the same repair twice in eighteen months. A driveway that carries vehicle loads also has to be built to a compaction spec, and getting that wrong is expensive to undo.
If you want a straight read on whether it’s a repair or a relay, call (844) 343-6681 and we’ll schedule a free estimate with a written price in hand.
FAQs

A properly installed Silestone paver driveway should hold 25 to 30 years or more, and the pavers themselves often outlast the base under them. The failure point in our climate is the substrate and drainage, not the quartz surface, which is why installation quality decides the lifespan.
Yes, in many cases – if the base under that section is sound, we can lift, re-bed, and relay with matched Silestone pavers rather than tearing out the whole driveway. If the base has settled or the edge restraint is failing, a patch won’t hold, and we’ll tell you that plainly with the price for each option.
A small repair section is typically a one-day job, while a full driveway relay runs several days depending on square footage, excavation, and curing time. You get the schedule in the written scope before work starts, so you know what to expect.
We source matched pavers from the documented Silestone paver line that fits your installation, and we confirm thickness, color line, and finish before ordering. We don’t carry parts on a truck – each job is specified and ordered to the project – which is why we measure first and quote in writing.
Bradford Remodeling Co Los Angeles is an independent service provider and is not affiliated with Silestone.
Call (844) 343-6681 for a free estimate. A live person answers, 24 hours a day, 7 days a week, and you’ll have a written price before any work begins.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












