







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Wellborn Driveway & Pavers: The Los Angeles Owner’s Guide
If you’re pricing a Wellborn driveway and paver package in Los Angeles, the installed cost typically runs $8,260 to $21,240 for a paver driveway, with concrete at $5,310 to $14,160 and a full replacement at $5,900 to $16,520. Those numbers include the substrate prep that actually decides how long the surface lasts. We install and restore Wellborn-spec paver systems and can usually get an estimator to your property within a few days of your call.
Owners rarely notice the failure first on the surface. They notice it at the edge, where a paver has lifted a half inch and catches a shoe, or in the low corner of the driveway after the first winter rain, when a puddle sits for three days instead of draining. That standing water is the tell. It means the base under the pavers has shifted, and the visible tile is just the last thing to go.
Key Takeaways
- Wellborn paver driveways in Los Angeles usually land between $8,260 and $21,240 installed, depending on square footage, base depth, and edge restraint.
- Most Southern California paver failures trace back to base and drainage, not to the pavers themselves.
- Sealing runs $295 to $825 and is the cheapest way to stretch the life of a sound driveway.
- We are an independent contractor and are not affiliated with Wellborn.
Which Wellborn Models This Applies To

Wellborn’s paver line is sold by profile and format rather than by a single model number, so the first job is identifying what you actually have. Wellborn’s tumbled and smooth-face pavers come in standard modular dimensions (commonly 4×8, 6×9, and 12×12 inch formats, with some plank profiles), and the joint width and chamfer on the edge tell you which series you’re replacing. A genuine Wellborn piece will have a consistent 1/8 to 3/16 inch spacer bar or chamfer; if the neighboring pavers are thinner, someone already patched it with a generic block and the color will drift within a season.
The compatibility trap here is color lot. Wellborn runs dye lots, and a 2025 “Sierra” or “Cobble” paver will not match a 2019 batch of the same name under Los Angeles sun; the older material has faded toward gray while the new stock reads warmer. Pull one paver from a hidden corner and carry it to the estimator. A reputable replacement will match on format and lot or tell you the whole field needs re-laying for a true color match.
On original equipment versus aftermarket: Wellborn pavers are premium and worth matching when the driveway is sound and you’re replacing a damaged run. When the base is already failing, matching the original brand matters less than matching the format and thickness so the repaired section sits flush. We source through a documented brand roster that also includes Belgard and Unilock for close equivalents where a Wellborn lot is no longer available.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Wellborn Driveway & Pavers Is Failing
- Paver lift and rocking (“tenting”). One or two pavers sit proud of the field and rock underfoot. The cause is almost always trapped moisture in the base freezing or swelling, or a missing edge restraint letting the field creep outward.
- Standing water in the low corner. Puddles that last more than a day mean the driveway has lost its slope or the base has settled. In Los Angeles this shows up fast during the winter rains that hit hard after months of dry ground.
- Sand washing out of the joints. Wide, empty joints with sand pooling at the apron or gutter point to joint sand loss and water moving through the field instead of off it.
- Efflorescence and white haze. A chalky white film that returns after rain is mineral salts migrating through the paver. It’s cosmetic on a sound driveway but signals water is saturating the surface.
- Edge settling at the apron or foundation wall. A dip where the driveway meets the garage slab or street gutter is a base failure, not a surface one, and it’s the symptom that most often leads to a full replacement rather than a spot repair.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what the numbers look like across Los Angeles, and each figure reflects a written price before any work begins:
- Paver driveway installation: $8,260 to $21,240
- Concrete driveway installation: $5,310 to $14,160
- Asphalt driveway paving: $4,130 to $10,620
- Driveway replacement: $5,900 to $16,520
- Driveway sealing: $295 to $825
The range moves on three things: square footage, base depth (a Los Angeles driveway on expansive clay soil often needs a deeper compacted aggregate base than the old surface had), and edge-restraint type. Labor includes excavation, base compaction, edge restraint, paver laying, and polymeric joint sand. We give you a line-item written price and won’t reprice it at the door. Every completed project carries the 365-Day Done Right Promise: if the work fails inside that window, we come back and correct it at no charge.
DIY or Call Us?
You can safely check a few things yourself. Walk the field and listen for hollow or rocking pavers. Pour a bucket of water at the high end and watch where it pools. Dig into a loose joint with a screwdriver to see whether the sand bed is still there or has washed away. That tells you a lot about whether you’re looking at sealing or a base problem.
Where it goes wrong is the base. Re-laying pavers over a settled or saturated substrate, or skipping the plate compactor, gives you a flat-looking driveway that lifts again after the next wet season. Using the wrong joint sand or sealing over a wet surface traps moisture and makes efflorescence worse. If the driveway is dipping at the garage slab or the aprons are pulling away, that’s a base and drainage job, not a weekend project. Call us at (844) 343-6681 for a free estimate and we’ll tell you honestly whether you need a repair or a replacement.
FAQs

How long does a Wellborn paver driveway last in Los Angeles?
Twenty-five to thirty years or more when the base is correctly built and the driveway is sealed every few years. The pavers themselves outlast almost everything else; the limiting factor is the compacted base and the edge restraint, which is why poor prep is what shortens a driveway’s life to ten or fifteen years. Call (844) 343-6681 for a free estimate on your specific driveway.
Can the failing section be repaired instead of replacing the whole driveway?
Yes, if the failure is localized to a spot like a lifted paver or a single low corner, and the color lot can still be matched. If the base is settling across the field or water is pooling in multiple places, a spot repair buys you one or two years before the same problem returns. We’ll tell you which one you’re facing.
How long does the swap or replacement take?
A paver driveway replacement is typically a three-to-five day job: one day to tear out and prep the base, one to two days laying, and a half day finishing joints and restraint. A sealing job is one day plus cure time. The schedule depends on square footage and base depth.
How do you source the Wellborn-compatible material?
We work through a documented roster of name-brand suppliers including Wellborn, Belgard, and Unilock, so specifications and manufacturer warranties are traceable. If a specific Wellborn color lot isn’t available, we’ll show you the closest format and shade match before you commit.
If your Wellborn driveway is showing any of these signs, call Bradford Remodeling Co Los Angeles at (844) 343-6681 for a free estimate. A real person answers the phone. We also work with KraftMaid, Cambria, and Silestone across our remodeling projects. Every job starts from a written price and finishes under the 365-Day Done Right Promise, backed by The Garrison Standard.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.












