







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Windows & Doors: The Los Angeles Owner’s Guide
We install and replace KraftMaid-compatible windows and doors in Los Angeles, with most window replacement projects running $5,310 to $17,700 and impact-rated installations running $9,440 to $29,500 installed, priced in writing before any work starts. Sliding patio doors, French doors, and tilt-in windows tied to a KraftMaid remodel are quoted the same way: part or unit cost plus labor, itemized, no moving numbers at the door.
Owners usually discover the failure the same way. A window that used to glide now needs a shoulder to close. A patio door drags on the threshold in one spot and seals tight in another. The glass fogs from the inside at the bottom corner after a Santa Ana wind week, or the frame near a west-facing wall feels warm to the touch by 3 p.m. in August. That last one matters in Los Angeles, where interior glass surface temps on west-facing units regularly climb well past 100°F in summer, and tired seals and weatherstripping fail years sooner than they do in milder climates. None of this means the whole unit is gone. It usually means one or two components are.
Which KraftMaid Models This Applies To

KraftMaid builds windows and doors to spec for individual projects rather than through a single fixed parts catalog, so the part that fits your neighbor’s unit may not fit yours. That’s the first thing we check. Every KraftMaid unit carries a manufacturer label on the frame or jamb, usually a small sticker or etched plate with the order number and unit dimensions. If that label is painted over or gone, we measure the rough opening and the visible glass area and compare those to the unit’s build sheet before we order anything. Guessing here is how homeowners end up with a sash that’s a quarter inch too tall.
Compatibility gotchas to know:
- Rough opening vs. unit size. The rough opening is the framed hole in the wall; the unit size is the window or door that goes into it. They are never the same number. Quoting off the rough opening alone is one of the most common ordering errors we correct.
- Left- and right-hand doors are not interchangeable. Patio and French door slabs are handed, and the hinge side determines the part. Confirm the swing before ordering.
- Impact-rated vs. standard glazing. Los Angeles County has fire-hazard zones and coastal wind considerations that push some units into impact or upgraded glazing specs. A replacement glass pack that isn’t rated to the original unit is a downgrade, not a repair.
- Finish and profile changes over time. KraftMaid updates frame profiles and finishes. A new sash can be a slightly different shade or trim line than the original. We tell you before you commit.
OEM versus aftermarket for KraftMaid specifically: OEM parts match the original spec, finish, and warranty chain exactly. Quality aftermarket equivalents (weatherstripping, rollers, hardware, glazing packs from established suppliers) are often chemically and dimensionally identical at lower cost, and we’ll tell you which ones are safe to substitute and which aren’t. We claim no parts in stock and no parts carried on a truck. Every part is sourced to your unit, then installed.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your KraftMaid Windows & Doors Is Failing
- Fogging or condensation between the panes. The insulated glass seal has failed and moisture is trapped inside the unit. This is a glass-pack replacement, not a whole-window replacement in most cases. Left alone, it spreads and clouds the whole pane.
- Drafts or water intrusion at the frame. Weatherstripping and corner seals break down with age and heat cycling. In Los Angeles, the dry summers and wet winters stress seals differently than steady-humidity climates, and a leaky corner will stain drywall and rot the rough opening behind it if it isn’t addressed.
- A door or window that won’t latch or seal evenly. Hinges sag, rollers wear flat, or the frame has shifted from settling. It may be a hardware fix, or it may signal a structural shift worth investigating. We diagnose which before quoting.
- The glass feels hot to the touch on a west-facing wall. The low-E coating or gas fill has degraded, letting heat through that the unit was rated to block. You’ll notice it in energy bills and comfort long before you notice the glass itself.
- Visible rot, cracking, or warping in the frame or sill. Moisture reaches the substrate and the wood or composite begins to fail. This is the one that escalates fastest. A compromised sill can let water into the wall cavity for months before you see it inside.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed price ranges for Los Angeles, using our standard written pricing:
| Project | Installed Range |
|---|---|
| Window replacement | $5,310 – $17,700 |
| Impact window installation | $9,440 – $29,500 |
The range moves on four things: unit size and configuration (a fixed picture window sits at the bottom; a multi-panel slider or a French door with sidelights sits at the top), glazing spec (standard vs. impact-rated vs. upgraded low-E), whether we’re replacing the whole unit or a glass pack and hardware, and access. A second-story window over a sloped roof or a door set into stucco gets priced for the extra setup. Every quote itemizes parts and labor separately, and the number you get is the number on the invoice. Completed work carries our 365-Day Done Right Promise: if the install or repair fails within a full year, we come back and correct it at no charge, in writing, signed.
DIY or Call Us?
What you can safely do: check the manufacturer label for the model and unit size, measure the visible glass area, note which side the door swings, and photograph any fogging, rot, or draft source. That information makes the quote faster and more accurate. What you shouldn’t do: remove a window or door from its rough opening, re-glaze a failed insulated unit on your own, or attempt to correct a frame that has shifted. Rough openings carry structural loads, and a misinstalled unit can leak into wall framing for months before showing on the interior. Window and door replacement also touches Los Angeles permitting and inspection in many cases, and doing it without the right pulls creates a problem at resale. If the frame or sill shows rot, stop and call. We’ll tell you straight whether it’s a component fix or a full replacement. Call (844) 343-6681 for a free estimate.
FAQs

A quality insulated unit typically holds its seal for 15 to 25 years, but Los Angeles heat cycling and UV exposure push the low end. West- and south-facing units often need glass-pack service in 10 to 15 years. We’ll give you a straight lifespan estimate for your specific unit at the quote.
Usually yes for fogged glass, worn weatherstripping, failing hardware, or a sagging hinge. A compromised frame, cracked sill, or structural shift usually means full replacement. We diagnose first and quote the repair before recommending the swap.
A single window or hardware repair is typically a few hours. A glass-pack replacement on an insulated unit runs 2 to 4 hours once the part is on site. Full window or door replacement is usually a day per opening, scheduled around your availability, with the site cleaned and squared away before we leave.
We source by the manufacturer label and the unit’s build sheet, not by year and general model guess. Where an OEM part is on long lead time, we identify a quality aftermarket equivalent, document it, and confirm it’s compatible before installing. You get the spec in writing before we order.
Where the work requires it, yes. Los Angeles permitting and inspection requirements vary by scope, and we pull what’s needed and pass inspection. The permit status is documented in your written quote.
Our 365-Day Done Right Promise covers it. If it fails within a full year, we return and correct it at no charge. The promise is written on your project documents, signed before work begins.
Written by the team at Bradford Remodeling Co Los Angeles, serving Los Angeles and nearby areas.
Part of the Garrison Partners family since 2004, Bradford Remodeling Co Los Angeles is an independently owned and operated business held to The Garrison Standard, and is not affiliated with KraftMaid. We also work with Cambria, Silestone, Kohler, and a documented roster of name-brand materials on every project. A live person answers the phone 24/7, background-checked and uniformed technicians arrive on every job, and every quote comes with a written price before work starts. Call (844) 343-6681 for a free estimate.












